Unified Computing System Discussions

Cisco UCS 6200 Series Fabric Interconnect To WS-C3560X-48 Help

Getting link down on the UCS FI6248 side when connecting an Uplink port to a WS-C3560X.Error on FI6248:descr="ether port 1/1 on fabric interconnect A oper state: link-down, reason: Link failure or not-connected" Configuration on WS-C3560X (showing Gi...

B230 Drivers

Hi AllI want to update drivers on my B230 m2 running ESXi, is it just the FNIC and ENIC which I have already done.Or are there other applicable or specific drivers for UCS Blades if so where can I grab them from...?I don't really want a whole ISO of ...

Resolved! Servers on C210 M2 all become unreachable

We have 2 UCS C210 M2 servers at 2 different locations. Over the past 2 months, they have each had the servers that are configured on them stop responding (including the ESXi host) and we are forced to reboot the CIMC in order for the servers to come...

Resolved! UCS Central DG Policy to modify local domain Admin PW?

Hello, I've looked in the UCS Central user guide and best practice doc, but I can't find any reference to UCS Central being able to set/modify the local admin account within a UCS domain. Is this possible? If so, what policy should I be looking at?...

Cisco Nexus 5k and Dell M8428-k interop?

Hi all,Is there anyone on the list who has experience hooking up a Dell M1000 bladechassis using M8428-k switches to a Nexus 5k/7k datacenter network? I'm particularly interested in CEE features and vPC. Thanks for giving me any pointers or info.Chee...

Expressway blade

Cisco Expressway is tested with which blades B200M3 or any other.I was trying to find out the link of valdiated blades.Thanks

C220M3 failed drive alarm via CIMC

Can I use the CIMC to tell the LSI MegaRAID SAS 9271-8i controller to stop beeping for X hours? Rebooting and pressing Control H to use the WebRaid GUI is not an option. The failed drive alarm is annoying those in the hallway outside the server room...

6248UP Fabric Interconnect HA functionality not ready

Hey Cisco community, last night I received two "Information" messages from UCS: Fabric Interconnect A, HA functionality not ready Fabric Interconnect B, HA functionality not ready A "Resolved" message I didn't received. Now I checked UCS, bu...

Resolved! UCS secure boot - should I enable?

C220 M3 server shipped with 1.5(4d). Looking to upgrade to ucs-c220-huu-2.0.1a. This is the recommeded release on cisco.com. Anyone have experience or recommendations on this? Should I use v2.0.1a and/or enable secure boot? Thanks!

B250 M2 unable to install Microsoft Hyper-V Server 2012 R2

Hi All, My Environment:2x FI 6248 (v2.2.1)2x 5108 Chassis1x B200 M21x B250 M2 I am experiencing an annoyed OS installation symptom. I tried installing Microsoft Hyper-V 2012 R2 on my B250 M2 blade but unfortunately it give error message "we couldn't ...

Resolved! How many UCS Domains can be supported by a UCS Central

Hello, I have a simple question about How many UCS Domains can be supported by a UCS Central? Thanks in advance.Paul

Resolved! C220 M3 with Cisco VIC and Onboard 1g?

Hello,We have a pair of C220 M3 servers that we have connected to a pair of fabrics (6248) for single-wire management through the VIC 1225. We'd like to also leverage the two on-board 1Gb NICs, however it is a bare metal Windows 2012 server and does...

C2200 Server with LSI Megaraid Software RAID and VMware

We currently run a few C220 servers using the LSI Megaraid software raid controller to create a number of Raid 10 arrays. I am pretty sure we had nor did not order any PCIe or Mezzanine RAID cards so we must be using the embedded Megaraid software co...

Cisco UCS C22 M3 Setup Error

Hi,We are setting up Windows Server 2008 R2 (64bit) on a new Cisco UCS C22 M3 server. We followed the Cisco guide to install a new Hard Disk in the new server and created virtual HDD( Array 0).(http://www.cisco.com/c/en/us/td/docs/unified_computing/u...