The specification sheet for the 6120 interconnect reports 8 pre-installed licenses are included:(http://www.cisco.com/en/US/prod/collateral/ps10265/ps10276/spec_sheet_c17-665945.pdf) "There are eight pre-licensed ports (out of 20) included with the C...
Using the vSphere Distr Switch, we set native VLAN per VM by setting the VLAN d to 0. How do we set the native VLAN for a VM if the VM is connected to a 1000V? I heard we no longer can use VLAN ID 0?
If I want to use VLAN 10 for management, I would have to configure the following:1000V -VM vEthernet port profile access port with VLAN 10, Ethernet uplink profile includes VLAN 10UCS - vNIC in Service Profile, include VLAN 10, and include VLAN 10 in...
Hello all,I'm experiencing this issue on my UCS-210 : on the Power Status in my VMWare it display : Power Supply 0 PSU_REDUNDANCY - Redundancy Lost ==> this give message Warning Power Supply 2 PSU2_STATUS: Power Supply AClost - D...
Hi,We are going to install 2 more additional chassis in existing setup, below is the list of existing setup and new chassis detailsExisting Setup Details: 2 x 6120XP Fabric Interconnect with 2.0(1t) firmware 2 x 5108 Chassis with 2 x 2201XP IOM and 8...
Hi,i couldn't find a documentation which states clearly how traffic flows from the mezanina adapter ports to FEX adapters. We have the A side and the B-side. that is for both fabric interconnecto and FEX adapters. does the B side actively send and...
I have a B230-M2 that is going to be SAN booted to a VNX with an MDS 9148 in between. The vHBA's are seen all the way through to the Array, but when I go to boot via the CD/DVD Virtual Media nothing comings up. The server goes straight to: Reboot a...
Can you connect a normal server (w/1gb NIC) to a fabric interconnect? As far as I understand it, the only possible way would be to configure an uplink port (which gets created as a trunk) which would require the server NIC to also be in trunk mode, w...
This was an ESXi host that I want to setup as a physical Server 2008 R2 server. Where I get hung up is the Installer give me grief that the partition is GPT and can't do the Windows one. So I attached the Driver DVD for the Cisco UCS B200 M2 and it d...
Hello,After having seen the VMmarks 2.1.1http://www.vmware.com/a/vmmark/core/32/?s_score=dAnd checking that UCS VMmark reaches the score using VM-FEX (http://www.cisco.com/en/US/prod/collateral/ps10265/vmm_infrastructure.pdf)One comes to the big ques...
With the vmware switches vDS or vSS, I see many designs are using the Active-passive approach for uplink NIC-teaming, i.e one vmnic is active going to fabric A, and one vmnic is passive going to fabric B. This is configured in vSphere.Se this articl...
Anyone seeing FaultCode F0391 - Description = Power Supply 1(2,3,4) in chassis 1 voltage:upper-non-recoverable.The chassis at this customer keeps reporting these across the four PS, then clears after approx 1 minute.Thanks!
Do you need to purchase ports for both the subordinate and active fabric interconnects? I assumed it would be one license per clustered pair. After applying a new license to a primary FI port I was able to download the same license to the subordinate...
I will be using vPC End Host Mode with MAC-pinning. I see I can further configure MAC-Pinning. Is this required or will it automatically forward packets by just turning it on? Is it also best not to enable failover for the vnics in this configuration...
