Hi, I have a new BE6H-M4-K9 and started to booting. When I hit F8 to do the ip address for cimc I am getting a blue screen which is asking for enter current cimc password, enter new cimc password , re-enter new cimc password. When I entered current c...
Hello.As you see a title, I want to know whether I should upgrade BIOS version of Cisco UCS (Cisco SNS-3655-K9).I`ve already upgraded CIMC like below.（4.1(3b) → 4.1(3f)）In this situation, Do I have to upgrade BIOS version to suitable oneand what is r...
Hi there,Can someone tells me is it recommended to use the vSwitch LB option "route based on IP hash" insted of originating port id in a UCS environment.I have 2 NIC's active active to the vSwitch ( FabA and FabB) and it was set to origination port I...
Hi Guys, Have you guys experienced after pressing F8 and going to CIMC screen, the keyboard stops responding so I can't navigate to the option to change the default password to CIMC. Can someone please share your experience and if you did and finally...
I am installing a new chassis and blades. I cloned the existing service profiles for the new blades. When installing ESXi 6.7, I noticed that the vmnic order has changed. The first four vmnics are labeled as MLOM but are listed last. If the MLOM port...
Hi, I am working with this server that has installed in the mLOM slot this module: https://www.cisco.com/c/en/us/products/interfaces-modules/ucs-virtual-interface-card-1227/index.html the appliance I am trying to install only works with eth0 and 1i...
I've got a weird issue with both of my C220 M5SX servers. I powered down my complete home lab to physically move/roll the rack 10metres across the room to a better spot, and now they are failing to power on/post. They are UCS managed and hooked direc...
Hi experts, I've been trying to determine some space allocations on a HyperFlex cluster via an ssh session to a Storage Controller VM. I've discovered that I can turn off the HyperFlex cleaner with the command stcli cleaner stop And I can start it ag...
Just looking for a little validation. Have a customer that deployed their environment using 4 x 10GbE connection as 4 separate uplinks versus creating a port-channel with the 4 interfaces. Is it possible to non-disruptively configure them in a port...
Hello,is anyone using redfish with this server model?I'm trying to deploy openshift bare metal IPI, it uses redfish to inspect the HW and it is not able to get the Ethernet Interfaces, CIMC replies with a 500 error:# curl -L -k --user admin:<password...
This has been posted here to reach a wider audience. If you find the same information on my blog, that's OK - I've posted it in both places!It all become possible when in ESXi v7.0U2, VMware introduced a new parameter for VMs called snapshot.alwaysAl...
Hi, As I understand it, the M3's I have across all my domains are no longer supported at this firmware level, that's fine, we don't want M3's anyway. What happens to them when the firmware is upgraded on the UCS? if they are not supported, and still ...
Hello Team,I have a couple of CIMCs that require upgrade due to some bugs. Last time I upgraded CIMC was ages ago so I believe some steps might have changed. I will be glad if you can guide me on this; All CIMCs run with this codesBIOS:C240M5.4.0.2a....
Hi everyoneI wanted to know if it is possible to install Cisco EPN v5 in bare metal in a UCS c240 M5.In the EPNM guide, I read that it installs on UCS 220.Thanks .
Hello,As a title, I want to know the recommended BIOS version of UCS and how to find where that information is posted.In addition, Cisco ISE is working under the UCS Server.Information about CIMC is like this.--------------------------------------●cu...
