Unified Computing System Discussions

Resolved! Cisco hyperflex edge deployment - duplicate IP address issue

Dear Team, Hope you are all doing fine. I am trying to deploy a 2 node hyperflex cluster using intersight. I created all the required policies, validated the configuration and start to deploy. During deployment it gets fails at 29% giving me an erro...

fsm-failed - F999984

Hi, we currently have a chassis with 4 B200 M5 blades working, we recently acquired 4 B200 M4 blades to incorporate them into the chassis, but when inserting one of the new new B200 M4 blades that arrived, the chassis showed the following critical al...

UCS M4 certification and conformance documentation: location?

I have a need to transfer Cisco UCS M4 220 (UCSC-C220-M4S) devices into several countries. There is an expectation that this will require certification and compliance documentation for those nations. I am unable to find a list of compliance documenta...

Boot order

I have installed my OS on two disks - i.e /dev/sda and /dev/sdc. What needs to be done if I need to boot OS which is on /dev/sdc. I don't see option to change the boot order in the boot order policy. In BIOS boot order I don't find logical name like ...

Clear fault in UCS

HiI have 24 warnings, that I can't clear.These warnings is from when our consultant configure UCS for us.I just want to delete them, but the only thing it seems I can do is do acknowledge them.Can someone please tell how to delete/clear these message...

Resolved! Cisco UCS B200 M4 System Board Replacement procedure

Hi, We need to replace a System Board on a Cisco UCS B200 M4 part 73-15862-04. Wondering were could I find a replacement procedure steps as the Cisco UCS B200 M4 Blade Server Installation and Service Note does not have that. Thanks,Roger

UCS Fault F4528227 - Pls Help

We have quite a number of alerts showing the fault ID "F4528227".Would you kindly advise what seems to be the cause and how to solve it?Thanks. (Examples)SeverityCodeIDAffected objectCauseLast TransitionDescription WarningF45282278982833org-root/la...

Black screen after press F8 UCS C220 M5

Last week we received one new Cisco UCS C220 M5 ( New out of the box) . I have some problems with the setup of CIMC . Normally you press F8 to config the CIMC , after the F8 you get the following screen for changing the default PW. After the change I...

Resolved! What is the C240 M5 warning threshold max for fans set as NA?

Hi, Checking on CIMC, I realised that the warning threshold max value for fans on C240 M5s are set as NA. Is this intended if it is how can we monitor if the fan speed is spinning too fast?

Resolved! How-to "CISCO Serial Over LAN" on UCS Manager

In CIMC command line, there is a feature "CISCO Serial Over LAN" that one can directly connect KVM console over the terminal. I found very helpful for me when I troubleshoot a server lost connection for example: # scope kvm # connect host CISCO Seria...

UCSC-MLOM-C25Q-04 Incompatible Firmware and Drive message

Hi, We have an Hyperflex Cluster with 5 x HXAF240C-M5SX and 2 x UCS-FI-6454.In our server 3, we have an adapter compliance error message for the UCSC-MLOM-C25Q-04, "Adapter firmware and driver version not listed in HCL", however we have the same adap...

Resolved! UCS Bandwidth between vNICS

For this question lets say that I have a B200M5 with a 1440 VIC connected to a 2304 FE. I know the backplane between the blade and the FE is 40Gbps (I think 4x10Gbps in a Po).Let's say I create a service profile with 3 vNICs (mgmt, data1, data2). I k...

Resolved! Backup of Storage Controller Virtual Machine

Hi, It would be useful to make a backup of all Storage Controllers Virtual Machines? if yes, could I just schedule a backup with a backup solution like Veeam? or that could impact the installation, in that case, there is a "best practice" to backup ...

CISCO Modular Raid controller can not be detect by C240 M4

Hi! Experts:I know there is a bug in CISCO Modular Raid controller Due to Corrupted SAS Expander Firmware. The Raid controller can not be detected by the server. Is there any instruction how to over come this for stand alone C240M4?Thanks!Grace

Resolved! Using HX Native Snapshots after VMware Snapshots were in place

hyperHello, I read that it's recommended to take an initial HX native snapshot on all VMs on the HX cluster (Sentinel snapshot), however we never did that and now we have a backup solution that is taking VMware snapshots in every job. How can I switc...

Unified Computing System Discussions

Forum Posts

Resolved! Cisco hyperflex edge deployment - duplicate IP address issue

fsm-failed - F999984

UCS M4 certification and conformance documentation: location?

Boot order

Clear fault in UCS

Resolved! Cisco UCS B200 M4 System Board Replacement procedure

UCS Fault F4528227 - Pls Help

Black screen after press F8 UCS C220 M5

Resolved! What is the C240 M5 warning threshold max for fans set as NA?

Resolved! How-to "CISCO Serial Over LAN" on UCS Manager

UCSC-MLOM-C25Q-04 Incompatible Firmware and Drive message

Resolved! UCS Bandwidth between vNICS

Resolved! Backup of Storage Controller Virtual Machine

CISCO Modular Raid controller can not be detect by C240 M4

Resolved! Using HX Native Snapshots after VMware Snapshots were in place

Congratulations to the Event Top Contributors Class of 2024!

Cisco + Splunk: It's a new day for your data.

A new chapter of the Spotlight Award begins!

Join us in Celebrating the New Year and the Nov.-Jan. Winners!

Announcing Resources That Guide You to Success

About IMM mode UCSX X9508 rediscover or reboot question

Firmware Cleanup Script

PowerShell- Add a UCS vLAN Group to an existing vNIC Template

Download Inventory using Api

UCS CIMC - Boot/Crash recordings

CIMC ip for a FI-attached C240-M6 server in IMM

Upgrading IOMs manually

Download software bundle / firmware without support contract?

FCoE Issues

VMWare ESXi 7.0U3p Cisco Custom Image