I recently got my hands on a Cisco C240 M4SX with 24 drive bays. It’s equipped with a Cisco 12G SAS Modular RAID Controller, but I’ve run into an issue I can’t seem to solve.From what I’ve read, using a non-Cisco PCIe adapter causes the system fans t...
Forum Posts
I have a Cisco UCS C240-M5L and I would like to know if there is a software I can install so our RMM software can see all drives on the raid controllers to alert us for drive failures. On HP servers, I can do this if I install Smart Storage Administr...
Good afternoon guys! I have been helped by the community already with a previous issue so thank you all for that sincerely! At the moment I have 8 drives being read by my C220 M4 Server with a Raid HBA Card, I want to access the raid configurati...
Hello,Since 6536s have 40G ports we're using CVR to connect the 5108 chassis to FI. Server port is coming online for a minute and then we're losing connection to chassis and IOMs. Any thoughts? TIA.
Resolved! C220-M5 Optane DCPMM Requirements
Does anyone know if the requirement for 2 CPU population on a C220-M5 has been lifted for Optane DCPMMs? I would like to add two 128GB Optane DCPMMs to my existing 1 CPU config.
Resolved! UCS C220 M4 HDD/Raid Troubleshoot
Good morning, techies! I just got a new Raid Card installed and have 8 HDD installed into the server. However only drive bays 5-8 show up, drives 1-4 do not show up but I have switched them around and always only bay 5-8 show up. I see that the backp...
I was configuring service profile template for ESXi hosts and followed best practices works fine, for Windows 2022 Hyper-v I am confused how to configure vnic, trunk port or native VLAN ? FI ports are port channeled by default, how to define vnic for...
I have a UCS 5108 chassis with eight B200 M5's, I upgraded the chassis manager from 4.3.4a to 4.3.5a at Christmas time but when upgrading a blade from 4.2.1f to 4.3.5a this week it failed at the following step:Associate Check Power Availability - Che...
I've been using a UCS C240M4 for quite a while with an external kvm but figured maybe someone here could help me get the onboard vkvm working. When launched from CIMC I get no keyboard or mouse input. Just recently updated to the latest firmware with...
Hi, We have a new deployment of 2x C220M6 servers, standalone mode, both with UCSC-PCIE-C25Q-04 adapters installed, but when logging into the CIMC GUI and clicking into these, we get the following error message: Unable to communicate with Card (actio...
I knew the C240M4 is not officially support them on the list, but just wonder with the firmware version C240M4.4.1.2f.0.1024230116, is it possible to run with any new (comparing to the official list) version of GPUs, e.g. v1000, A5000?
I am trying to relocate one of the Chassis(2) and subordinate FI to different rack in same location without downtime. ENVIRONMENT: FI model: 6200 (EOS) Chassis Model: UCSB-5108-AC2 2 FI's connected to 2 chassis (blade servers) with high availability ...
Hi everyone,I have a Cisco C220 M4 server with the following firmware versions:BIOS: C220M4.3.0.4c.0.0502191259CIMC: 4.1(2m)The issue I'm facing is that the fans are spinning at extremely high speeds, generating excessive noise, although they are rep...
Hi Everyone,I have a C220 M4 that was previously connected to UCS and is now being used as a standalone server.CIMC is configured and accessible via KVM. Two Ethernet cables are connected and show up in CIMC under External Interfaces.However, the OS ...
I have apic on UCS C220 M5 Rack Servers. I update CIMC and other components using HUU to version 4.2.2a. After update CIMC GUI is not responding. I can ssh to CIMC ip address and the apic is seen in aci fabric as Fully fit. I have rebooted cimc, disa...
