Hi!We had a broken disk on our cisco ise server which is setup using Raid 10.Went out with a new disk same size and everything but different brand, Seage instead of Thosiba BUT everything else is indentical.The disk shows up fine in CIMC, but says Un...
Forum Posts
UCS manager firmware upgrade is not working. All UCS B200M3 servers are running version 4.1.3nb, but the chassis I/O module and fabric interconnect are not upgrading.
I recently got my hands on a Cisco C240 M4SX with 24 drive bays. It’s equipped with a Cisco 12G SAS Modular RAID Controller, but I’ve run into an issue I can’t seem to solve.From what I’ve read, using a non-Cisco PCIe adapter causes the system fans t...
Hello,Does anyone have a link to a repository or would care to share the BIOS, CMC, and other drivers found in the latest Host Utility updates for the C240 M3 & M4?I have spent hours trying to update this firmware, I have scraped the internet trying ...
How to reset password that is forgotten for C220 M5SX? what i remember is that even if we reboot the server and press F8 and then F1 after the getting the IP address screen and if we tried to change the password it will still ask for old password to...
Resolved! VMWare ESXi 7.0U3p Cisco Custom Image
Does anyone know with Boardcom acquiring VMWare, will Cisco still come out with the latest ESxi 7.0U3p, that contain the security fix for ESXi 7.0U3o?Thanks,
Old neglected DEV environment. Not on support, so no TAC case possible.UCS Central 2.0(1r)UCS Manager 4.2(3i) on 6248UP pairI found how to recreate the certs in CLI for Central and Manager and did that.I found how to set the shared secret in CLI for...
I have a Cisco UCS C240-M5L and I would like to know if there is a software I can install so our RMM software can see all drives on the raid controllers to alert us for drive failures. On HP servers, I can do this if I install Smart Storage Administr...
Good afternoon guys! I have been helped by the community already with a previous issue so thank you all for that sincerely! At the moment I have 8 drives being read by my C220 M4 Server with a Raid HBA Card, I want to access the raid configurati...
Hello,Since 6536s have 40G ports we're using CVR to connect the 5108 chassis to FI. Server port is coming online for a minute and then we're losing connection to chassis and IOMs. Any thoughts? TIA.
Resolved! C220-M5 Optane DCPMM Requirements
Does anyone know if the requirement for 2 CPU population on a C220-M5 has been lifted for Optane DCPMMs? I would like to add two 128GB Optane DCPMMs to my existing 1 CPU config.
Resolved! UCS C220 M4 HDD/Raid Troubleshoot
Good morning, techies! I just got a new Raid Card installed and have 8 HDD installed into the server. However only drive bays 5-8 show up, drives 1-4 do not show up but I have switched them around and always only bay 5-8 show up. I see that the backp...
I was configuring service profile template for ESXi hosts and followed best practices works fine, for Windows 2022 Hyper-v I am confused how to configure vnic, trunk port or native VLAN ? FI ports are port channeled by default, how to define vnic for...
I have a UCS 5108 chassis with eight B200 M5's, I upgraded the chassis manager from 4.3.4a to 4.3.5a at Christmas time but when upgrading a blade from 4.2.1f to 4.3.5a this week it failed at the following step:Associate Check Power Availability - Che...
I've been using a UCS C240M4 for quite a while with an external kvm but figured maybe someone here could help me get the onboard vkvm working. When launched from CIMC I get no keyboard or mouse input. Just recently updated to the latest firmware with...
