Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
rarmitage
‎03-18-2021

Beginner
Recent Badges
Awards
Recent Badges
See all
10 Helpful Vote
1 Helpful Vote
1 Accepted Solution
10 Replies
5 Replies
Stats
Member since ‎10-09-2007
29
Posts
20
Helpful
1
Solution

Initial Announcement for Hunt pilot not playing when transferred from call handler

Created by in Unified Communications Infrastructure
03-05-2021
03-05-2021
When I dial directly into the Hunt Pilot I get the Initial announcement played. We I transfer in fro...

Re: ISR 4321 Rommon ugrade Fails

Created by in Routing
10-31-2018
10-31-2018
I just had to change flash: to bootflash: and it worked

ISR 4321 Rommon ugrade Fails

Created by in Routing
10-31-2018
10-31-2018
I am trying to upgrade the rommon on a ISR4321/K9 and get the following error. TEST_NAT#upgrade rom-...

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router

Created by in Switching
10-23-2018
10-23-2018
Thanks I thought a 110 watts was too low run a POE Module.

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router

Created by in Switching
10-23-2018
10-23-2018
sh invNAME: "Chassis", DESCR: "Cisco ISR4321 Chassis"PID: ISR4321/K9 , VID: V04, SN: FLM2235W136 NAM...

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router

Created by in Switching
10-23-2018
10-23-2018
sh platform diagChassis type: ISR4321/K9 Slot: 0, ISR4321/K9 Running state : ok Internal state : onl...

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router

Created by in Switching
10-23-2018
10-23-2018
NAME: "NIM subslot 0/1", DESCR: "NIM-ES2-8-P"PID: NIM-ES2-8-P , VID: V01, SN: FOC22225QUA Above is t...

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router

Created by in Switching
10-23-2018
10-23-2018
There was no output

NIM-ES2-8-P Not giving POE when installed in 4321 router

Created by in Switching
10-23-2018
10-23-2018
have a NIM-ES2-8-P installed in my 4321 router and I am not getting power for a Cisco 7945 IP phone....

Re: Hunt Pilot Line Group CDR Reporting

Created by in Unified Communications Infrastructure
02-23-2018
02-23-2018
Thanks Rob I changed both Show Line Group Member DN in finalCalledPartyNumber and Show Line Group Me...

Hunt Pilot Line Group CDR Reporting

Created by in Unified Communications Infrastructure
02-20-2018
02-20-2018
I have a Hunt Pilot Group set up and I trying to run reports on who in line group picked up the call...

I am trying to make the same

Created by in Switching
10-13-2015
10-13-2015
I am trying to make the same decision. Ar you happy going with the Nexus?

I tried that config and the

Created by in IP Telephony and Phones
05-28-2015
05-28-2015
I tried that config and the call goes in but I only get "From O" as my caller ID on all calls.

Virgin mobile phone will not connect

Created by in IP Telephony and Phones
05-27-2015
05-27-2015
Virgin Mobile Phone rings once and then goes to fast busy when caller id is enabled. Works fine when...

Thanks everyone. That did the

Created by in IP Telephony and Phones
05-14-2015
05-14-2015
Thanks everyone. That did the trick.
Public Statistics
Date Registered ‎10-09-2007 09:41 AM
Date Last Visited ‎03-18-2021 06:19 AM
Total Messages Posted 29
Total Helpful Votes Received 20
Helpful Votes Given To
Helpful Votes From