Hi, could you please be more specific about 5Ghz? Hue bridge is connected via cable, iphone is connected to the same subnet via AP. Hue app from iphone can control all lights but SIRI control is not working because hue cannot be added to apple home kit. And that is happening because apple relies on bonjour which likes devices to be on the same broadcast domain while when using WLC+AP you have some tunneling involved. I'm really bad but multicast and tried to setup some proxy but had no luck there. So if you have workign setup would be nice to see it but for some reason I think you incorrectly interpreted original question.  ... View more

No, just created another vlan ( ... View more

Hi,   Exporting from lab to production - have too many user variables. As to ECC - they are always the same so would be nice to have a template for a new deployments.   Thanks,   Vlod ... View more

Hi,   Do I have same issue?   I have BVI created and assigned there one subinterface and one physical port:   interface BVI2 nameif Guest security-level 10 ip address 192.168.10.254 255.255.255.0 interface GigabitEthernet1/3 bridge-group 2 nameif Guest_2 security-level 10 interface GigabitEthernet1/2.2 vlan 2 bridge-group 2 nameif SwTrGuest security-level 10   I have 2 hosts: one is connected through switch (trunk from asa port GigabitEthernet1/2.2 ) and another one connected directly to  interface GigabitEthernet1/3. I cannot ping each other although they have IPs from the same subnet.    But I can ping both of them from another VLAN interface GigabitEthernet1/2.10   interface GigabitEthernet1/2.10 vlan 10 nameif TEST_Vlan security-level 100 ip address 10.221.11.254 255.255.255.0   Why 2 hosts in the same BVI cannot communicate (same security level) but can speak to other hosts? Do I need to apply ACL?   Thanks, ... View more

One of the strategies can be:  - full DB update weekly  - incremental DB backups daily  - regutil for registry backup. For sql server to be able to store files on a remote share, you backup source server (logger/aw) should have write permissions on a remote share. ... View more

Hi Geoff, Thank you for the reply. I've changed the deployment type but it wasn't helping. Checked one of the production system with co-resident CUIC/LD/IdS and it has some extra services showing when getting info through the REST API: Live Data is enabled, etc. So will try to setup that thing first, if no - just install standalone IdS. Thank you, UPD:  Rebooted after changing deployment type - then it worked) Now have troubles as my PGs are co-resident with central controller but that will be another story. Thank you for help ... View more

Hi guys,  I can see here quite hardcore discussion with SQL queries that are not mentioned in the install guides so will ask for help. Have Dev Environment of UCCE 11.5 with Progger 450agents (now Progger (Lab only) ) Installed coresident CUIC/LD/IdS as want to test SSO. Trust is built between ADFS-IdS, Test SSO button on IdS works). On cceadmin page I've added Finesse and CUIC-LD-IdS Publisher and Subscriber was auto added - so nothing unusual. Now when I try to register components for SSO, this CUIC/LD/IdS publisher refuses to register: The following machines failed to register or set SSO mode: cuic01.lab.com Invalid machine. Missing Default Identity Service But on the inventory page there is no filed to provide  Default Identity Service for IdS itself.  I tried manually to update t_Machine_service table with Uri for this host but it didn't help. Changed deployment type to 4000 Rogger but no luck. Am I missing something obvious or this can be fixed with SQL/REST? UPD: rest request gives this text: <ssoComponentStatus> <apiErrors> <apiError> <errorData> CUIC_PUBLISHER </errorData> <errorDetail xmlns:xsi = "http://www.w3.org/2001/XMLSchema-instance" xsi:type = "valueErrorDetail" > <value> IDS_PRIMARY_REF </value> </errorDetail> <errorMessage> Machine requires service type IDS_PRIMARY_REF. Ensure that a uri is configured for this service that references the primary Cisco Identity Service for this machine. </errorMessage> <errorType> inventory.machineTypeInfoNotValidServices </errorType> </apiError> </apiErrors> <modeState> NOT_STARTED </modeState> <name> cuic01.lab.com </name> <refURL> /unifiedconfig/config/machineinventory/5045 </refURL> <registrationState> FAILED </registrationState> <ssoTestPath> https://cuic01.lab.com:8444/cuicui/sso/test </ssoTestPath> </ssoComponentStatus> Thank you ... View more

Interface Name................................... management MAC Address...................................... 68:86:a7:36:b5:00 IP Address....................................... 192.168.9.252 IP Netmask....................................... 255.255.255.0 IP Gateway....................................... 192.168.9.254 External NAT IP State............................ Disabled External NAT IP Address.......................... 0.0.0.0 Link Local IPv6 Address.......................... fe80::6a86:a7ff:fe36:b500/64 STATE ........................................... REACHABLE Primary IPv6 Address............................. ::/128 STATE ........................................... NONE Primary IPv6 Gateway............................. :: Primary IPv6 Gateway Mac Address................. 00:00:00:00:00:00 STATE ........................................... INCOMPLETE VLAN............................................. 100 Quarantine-vlan.................................. 0 Active Physical Port............................. 1 Primary Physical Port............................ 1 Backup Physical Port............................. Unconfigured DHCP Proxy Mode.................................. Enabled Primary DHCP Server.............................. 192.168.9.252 Secondary DHCP Server............................ Unconfigured DHCP Option 82................................... Disabled DHCP Option 82 bridge mode insertion............. Disabled IPv4 ACL......................................... Unconfigured IPv6 ACL......................................... Unconfigured URL ACL.......................................... Unconfigured mDNS Profile Name................................ Unconfigured AP Manager....................................... Yes Guest Interface.................................. No ---------------------------- interface GigabitEthernet0/7 description === WLC 2504 Trunk === switchport trunk encapsulation dot1q switchport trunk allowed vlan 2,3,100 switchport mode trunk end On the switch tried management as Native Vlan too. switched to tagging. ... View more

Hi, I cannot access it via wired. It is the same VLAN 192.168.3.0 for both wired and wireless. Initially I'm on a wired network. As soon as I span this wired network to wireless - I loose connection. Tried that checkbox now - didn't help. Thank you, ... View more

Hi, Did you manage to find a reason? I have the same problem. Don't think it is phone as whispering is working. Could you please also advise what file name do you have on mediaserver? agentgreetingtype_agentID.wav? regards, Vlod ... View more

Hi alshahiry, You asked strange question - you getting strange responce )). Please do not use in production and do not expect any support from cisco on this setup. Theoretically if you assign same name to CUCMs (but they will have different IP) you would be able to achieve redundancy using DNS. Let say you use name "cucm_pub". Configure DNS entry for "cucm_pub" specifying primary IP of CUCM1 and secondary IP of CUCM2. In DHCP server for the phone use domain name "cucm_pub" for specifying TFTP option. So the phone will go to CUCM1. If the CUCM1 goes down DNS should tell the phone IP address of CUCM2 and phone should go there. For this to work you will also need completely to replicate the setup from CUCM1 on CUCM2 (some sort of HSRP). Again it is just to proove that this should be possible to make. ... View more

You are trying to failover phone to a different cluster. (each CUCM publisher in your case is a different cluster). Technically you can do this (just as proof of concept) by configuring same doamin name and then using DNS server to have redundant entry for the domain name. But what you need is re-install one of the servers and build it as a subscriber, add to existing cluster. Then you will be able to see both servers under "CallManger servers" menu, youi can add then both to CUCM group. ... View more