Hi all,i'm tryng to setup call forwarding by phone connected to a spa122 with code *72+number but i receive a strange tone and no more working until i make *73 (otherwise i've a busy tone)...some idea ? when i make *72 i'm not able to receive call un...
we observe the following problem if provisioning the SPA122 for bridge mode:1. SPA122 factory default, FW 1.1.0(011)2. SPA122 gets config file (XML) with:**<router-configuration> <Router_Mode>0</Router_Mode>...</router-configuration>** - this shou...
I'm looking to arrange all 4 of my incoming lines (Shared FXO Entensions) to the left side of my SPA509G. By default it looks like it puts them it its own order. How can I move these? Otherwise I'm stuck with the phone extension at the top right t...
Hello,I have an UC560 and I upgrade the Software Pack to 8.1 and change Language Pack to French.I connect Phones SPA5xx and it's fine.With cisco 7937G it reboot always.The last one with another UC540 I enter in conf t and enter this command line :tft...
First of all, I apologize for this question, I´m sure that it is answered somewhere, but it took me some hours and I´m in a little hurry.I have an UC560 with IOS 15.1(2)T2 and software package 8.1.0. CCA is version 3.0.I have connected an Cisco IP Ph...
Hi members, I have a UC540 which has not had any configuration changes but the user suddenly cannot make any outgoing calls. The Incoming is working fine and the Trunk Status shows it connected.The provider says the calls are not hitting their gatewa...
Hi all,what does this result means while put command :: show call active voice briefED2 : 19714 10:57:18.742 ZP4 Sat Jun 8 2013.1 +540 pid:51 Answer 042591773 active dur 01:23:00 tx:369/61674 rx:481/73684 Tele 0/1/1 (19714) [0/1/1] tx:4980520/49805...
HiI wonder if anybody had managed to configure SPA112 (HardwareVersion 1.0.0, SoftwareVersion 1.3.1) with TR-069. I experienced with Perl ACS server implementing CWMP protocol ( https://github.com/dpavlin/perl-cwmp.git ) and when I am trying for exam...
Hello,We have a communication device connected to an FXS port on the SPA122 (HW v.1.0 / FW v.1.3.2(014)) that dials out to another device that auto answers and then hangs up upon completion of a task. The problem is that, upon termination intiated a...
this happens lately on outgoing calls.. incoming are not the issue.. not sure where to start troubleshooting.. the system worked fine
If the VIC2-2FXO is added to the UC540 do we need to purchase any additonal licenses to have these 2 FXO ports activated?
We have supplied one UC320 box with 3 number of SPA303-G2. Now customer want to call to IP Phone of Italy office without adding any extra cost. I can create a VPN between these branches. is it possible to call to Italy IP phones extension after creat...
Hello. I want to see if anyone else is experienceing this issue. UC320WThis device is the second one I have had that has after a month or so of service begins to experience line quality issues. Users report- line echo, crackling, call break up and m...
Quick question, we have a client that is moving offices and finally wants to make the move to IP phone system. They are purchasing comcast business voice service. Will this service interface with the UC320 or do we need to move them into a UC540? Thi...
I found that my customer UC540 cannot detect remote party disconnect tone, while at AA or after conversation with calls. I already set CPTone to Malaysia, which is MY. This is second time I am facing this issue and I have to set a difference cust...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: