I have used the Config Wizard to set up the UC520 but I am having DNS issues when trying to gfet out to the internet. When I check the System Status it shows "None" under the Gateway column. Under Routing/Internet Connection/FastEt...
I have used the Config Wizard to set up the UC520 but I am having DNS issues when trying to gfet out to the internet. When I check the System Status it shows "None" under the Gateway column. Under Routing/Internet Connection/FastEt...
Hello,I need some help with the following problem Call Pickup or Directed Call Pickup gives One Way Audio on a SPA525G. It doesn't mater if you use *98 or *97 followed by the extension of the phone to pickup the call from another phone that is ringin...
Hi,I have a UC560 that's been installed by our telecomms partner - over the course of the past 2 months I've been learning lots about the UC560 (even though I was a Cisco virgin prior to this!) and it's plentiful...quirks shall we say!At the minute w...
Hi,I have a Cisco SPA112 which connects to a 3CX server. I also have addional phones, inluding Cisco SPA504G phones.The issue I have is the SPA112 reboots every 3 days, exactly to the minute. This has happened 3 times now. The 504G is fine (40+ days ...
Quick question to the Cisco team. Any chance on knowing what you guys are working on for release 2.4 of the firmware?Regards,Paul.
I have an auto attendant that goes to six options.each option goes to a hunt group. I then need voicemail at the end of each queue on an extension.I get "the is no mailbox associated with this extension"Typical config is hunt group 501 rings 201, 202...
Dear Experts,I have CME with 2 phones configured with same DN. Is it possible, that when I have a call on one of the phones, to switch the callto the other one? I yes, do I need anything special in configuration?I know that I can use a park position ...
As I have not been able to find any way to submit a support case to Cisco regarding these phones, and in hopes that someone from Cisco may see this, I'd like to request full support for RFC 4235 in the SPA-50x series phones. This is so that in SIP pr...
Hello,Setup is UC320 with 20 phones. Reception has a phone with sidecar configured with line monitor for first line of all phones.All standard phones have voicemail disabled.The problem is that when staff put their phones on DND the line monitor at r...
Hello, I have a problem with FXS ports in a UC-540.Every time I reboot the UC-540 assigned a new mac-address on FXS ports.Anyone can help me.Thank you.
On our UC540, we have set a couple of numbers for Single-Number Reach to call our Cisco Jabber enabled iPhones. Since they are a different extension than our primary extension, the voicemail box is a different mailbox that the primary number called, ...
Incoming calls are sent to 6 phones simultaneously via a hunt group. One phone has voicemail set up but it only activates when called internally. The system is 9000/400 with spa941 phones.The hunt group was set up using the wizard so it is my underst...
HiFirst, sorry for my english . i have five SPA504G and always, i have always set for web http://ipx.x.x.x. Now I have 30 phones and I need to set it automatically, without doing it by web. Is there any application or way to do it?I searched forums b...
Hi, I would like to personalized the background of my equipments. I have a UC520 and 560, using CCA (Cisco Configuration Assistant) I have uploaded the backgrounds (correct size 320 x 212) and according to the added image, made auto-generated List.XM...
Hi I have a 320w system with spa8800 and 13 cisco ip phones,i need help to set up recording live calls in some of the extensions in my system bt cannot find any information about this in cisco support and cisco chat support seems likeis not working c...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: