VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

Hey everyone - got a question I hope you guys can sort out for me.  I've got a setup with (to start with) two office, both with ASA's and both with dual WAN connections (different providers) on each with failover configured using tracking - this part...

rjberetto by Level 1
  • 9376 Views
  • 12 replies
  • 0 Helpful votes

  Hi,I have configured an easy vpn server in cisco 1905 ISR using ccp. The router was already configured with zone based firewall. With the help of vpn client i can reach only upto  the internal interface of the router but can't access the LAN of my ...

I can ssh to the routers 10.1.3.1 int but not to the 10.1.3.x dhcp clients. Before the internet access and nat stuff was added to this config ssh worked.The problem is when performing ssh to a 10.1.3.x unit from a 10.1.1.x unit. They get a login and ...

kuesteral by Level 1
  • 9650 Views
  • 14 replies
  • 0 Helpful votes

I have consulted a Cisco partner, as well as two different sources at Cisco and it seems remarkably difficult to find someone with solid answers on anyconnect mobile licensing. I've got a pair of 5550s running 8.3.2 in active/standby. Based on the fo...

Hi All,I have my SSL-VPN (SONICWALL) box behind Cisco ASA box, I have done the Static NAT for the SSL BOX Im able to ping the box from internet, but not able to login to the ssl vpn webpage. Previously SSL box was working with the static public ip.An...

I am creating a IPSEC tunnel via a 3G Cell Interface to an ASA for failover in the event the primary Serial interface goes down.  Everything works just fine without the local switch connected to the 2811.  Cell interface comes up fine on failover wit...

Hello,I have idle timeout set to 10 mins for our IPSEC vpn group, however the tunnels are not disconnected when idle because data is still being sent/received by something.  i checked the statistics for the vpn client and can see bytes being sent/rec...

I need two branch routers 192.168.48.x and 192.168.49.x to be able to pass traffic to each other without a dedicated vpn tunnel between the two branches.HQ LAN is 172.16.x.x and 172.17.x.xBranch Routers use 192.168.x.x***PIX***access-list nonat permi...

I followed:http://www.cisco.com/en/US/products/hw/routers/ps274/products_configuration_example09186a0080819289.shtmlAnd my VPN connection is established on 2921.However when I successfully connected to the router via VPN,  ipfoncfig shows default gat...

bc4switch by Level 1
  • 906 Views
  • 2 replies
  • 0 Helpful votes

Is it possible to do the following on an ASA 8.2 (5). ( See attachment )  We have a site-to-site IPsec VPN with a client using only public IP's as the encryption domain. We want to have another IP on our side appear to come from the IP the client is ...

We have a vendor that we need to create a S2S VPN with and they are only allowing public IP addresses for the source address.  I assume this is because they don't want to deal with the potential overlap of private IP addresses from all of their clien...

deyster94 by Level 5
  • 2063 Views
  • 7 replies
  • 0 Helpful votes

   hi, i am jonathan rivero.i have an ASA 5520 Version 8.0(2), i configured the VPN site to site and works fine, in the other apliance i configured the VPN Client for remote users, and works fine, but i try to cofigure the 2 VPNs on ASA 5520 on the s...

Top Solution Authors