VPN

ASA 5520 V7.2.3the ASA is connected to Internet via a NAT devicewe try to establish a site-to-site VPN tunnel between this ASA and a remote firewall based on Openswan/Freeswan Linux software,using the usual preshared key method ; ...

I need to configure a RADIUS server, ACS if it's suported, to give a pre-defined IP address to a user connecting through PPP. The NAS asks RADIUS for authentication then receives the accept or reject and some parameter that should tell the NAS the IP...

I have the following dhcpd configuration:dhcpd address 10.1.1.5-10.1.1.7 outsidedhcpd enable outsideWhen I do show proc | inc dhcp ,I see the process, so it seems to be active. But when the client sends requests they droped on the outside interface ...

Hi, I trying to generate VPN Tunnel between every two routers in Tree type Wide area network in a project.I have done that but show crypto isakmp sa and show crypto ipsec sa are not showing results in previlege mode of router.I can ping other route...

I have worked on this brainteaser for a long time with no success, so any new perspectives will be appreciated. It's a challenging config - you'll see why.Hardware: Cisco 1841 Advanced Security BundleInterfaces: fa0/0 (internal network) fa0/1 (backu...

HiI have a setup as follPPOE client->LAC(Radius)->LNS(Radius)I face a strange issue only at the PPP authenticating phase.A snapshot of the debug PPP negotiation is as foll06:32:40: ppp67 PPP: Phase is ESTABLISHING06:32:40: ppp67 PPP: Send Message[Dyn...

Hello folks - We have a large number of people who are using the Cisco VPN client to connect to the corporate network. VPN autentication is being done using a Cisco ACS Server. Protocol being used is TACACS+. The issue we are running into is that whe...

Hello!How do I ensure that my VPN users that are connected using AnyConnect VPN to my ASA5520 have the same access restrictions/permissions as those connected locally? Assign a pool in the same vlan/subnet as those connected locally?Any input helps. ...

Hi,I will be installing ASA5510 behind a Interent rtr . The ASA5510 serves as pure EasyVPN server for remote cleints having 5505 to initiate RA.What TCP & UDP ports need to opened on Interenet rtr ACL to ASA5510 outside IP, so that the RA clients can...

Hello,i have a question about VPN Client for Linux.Is there any Client that works with a VPN3000 and multiprocessor ?I found only this Message:The VPN Client does not support SMP (multiprocessor) or 64-bit processor kernels.

Has anyone successfully configured a fax modem for remote console of a Cisco device? I found a Cisco doc on how to configure it, but i can't get the modem to work with secure crt or hyper term. Any particular dip switch setting?

Hi.I set up a L2L between 2 ASA, with site A needing to reach 2 different LANs on site B.For this purpose i wrote down these lines in the site B config:access-list outside_20_cryptomap extended permit ip 10.0.0.0 255.255.255.0 10.5.0.0 255.255.255.0 ...

I need to configure RA VPN in ASA 5520 for about 100 mobile users.set up isMobile users----->internet cloud------->1mbps.router1---->ASA---->inside n/w-----router2.8mbps-------->MPLS cloud---->512 mbps.eight Branchesrouter1, asa, router 2 are in data...

Many Kudos to the person who figures this one out...We have a VPN concentrator and about 15 1811's already in the field and working. We can't seem to get the latest one to work properly, we initially thought it was bad hardware, we are on our 3rd VPN...