VPN

I have configured Remote access VPN on Cisco ASA 5510 device. I am trying to configur split tunnel for th eusers but that does not work.I am creating an access-list for the split tunnel traffic i.e To Tunnel only traffic for ACLACL test <src IP> <Des...

Hello all,The problem here lies in the firewall blocking VPN traffic. Right now, as a lab, I've got the WAN port of the router set up with a xxx.xxx.xxx.158 255.255.255.252 IP address, and the LAN as a xxx.xxx.xxx.161 255.255.255.224 IP address.When...

We have ipsec vpn tunnel between cisco 2850 ipsec router and cisco 3015 concentrator. we used citrix traffic on this tunnel and it is working fine. When we replaced cisco 3020 concentrator for cisco 2850 router we have problem with citrix connectivit...

I have established the IPSec connection over the ATM. However, some traffic cannot pass through to the remote site. The ping testing is fine and they can browse over the Internet. I check the netstat which state that establish, such as terminal ser...

We are installing a BBSM in a multiLAN config. How can you get BBSM to function with network devices that are not on the same physical VLAN (broadcast domain) as the management VLAN? I can ping the network devices from BBSM but clients attempting to ...

Hi All Expert,Need help for PIX vpn to Sonicwall.I'd setup all the necessary configuration in both PIX and Sonicwall according to the Cisco documentation, but when I "show crypto isakmp sa" at PIX, it show the status in "OAK_CONF_ADDR", what is that ...

I have a web site which I can access from outside and works perfectly. When I try to access site using the VPN 3000 and WebVPN I keep ketting ASPScript errors in IE. The 3000 is basically the default configuration. Is there any setting which co...

I am unable to get my 3002 HW client to connect to my ASA Appliance. ASA debugging indicated Dynamic Crypto Map mismatch (the HW client DHCP derived IP address is whats being looked for). 3002 HW Client SW version 4.1.7HMode = ClientPAT enabledIPSec ...

Good day,On a PIX Version 7. We want to used a Cisco VPN client from the inside of this PIX to somewhere on the internet. We had this setup before with version 6.3. The only command we had to add was "fixup protocol esp-ike" and it work no problem. ...

I did that post already once, but didn't get an answer for it.When I use a second IP-Address on the same interface, the Cisco VPN-client is building up the tunnel, but it cannot get any packet through.This happens only with some IP-address combinatio...

I'm having trouble getting root certificates that are generated by my Win 2003 CA to work on my 3005 VPN Concentrator.I am attempting to get Citrix sessions to work through WebVPN sessions that are established with my concentrator. I can connect and ...

We are using VPN3020 for webvpn and client vpn access at the same time.when we use the webvpn to access Intranet, the performance is very slow and we can not get responding sometime.But, if we use VPN client to access Intranet, we get a very quick re...

We want to install VPN Clients on 1000 users machines. Is it possible to push and install the VPN Client software and the required Policy from a VPN 3030 concentrator to the designated Laptops? There is an ADSL private link between the remote lapto...

I want to configure authentication via ACS to ensure that users are using the correct client profile (some are more permissive than others, and I'd like to filter access in ACS). How can I configure ACS to check the group membership of a user when he...

i am faceing a problem when my clients trying to connect with hsp56 micromodem to cisco AS5300 access server.i am using access server IOS 12.2(2)XB10. can any one tell me what should i do to handle this problem?