VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

I want to do a R2R connection with VPN and access to INTERNET with these routeurs. I only have one serial interface by routeur. I use ISAKMP and I apply the crypto map (with "match address") on the serial interfaces which allow crypted telnet on a se...

egrellet by Level 1
  • 805 Views
  • 1 replies
  • 0 Helpful votes

I have a network of 2600 series routers connected to the internet using one provider each with a full T1 connection. I have an encrypted GRE tunnel between each site. I have done a few tests with bandwidth and if I bypass the tunnel, I get consiste...

8dgoswick by Level 1
  • 892 Views
  • 4 replies
  • 0 Helpful votes

we have a problem to configure a cisco 3005 for vpn access. the vpn is in parrallel to the firewall, so the problems shoulodn't be from there. I have connected the external interface directly to the internet (via cable and a cisco 2500) the private i...

Two sites are connected with a VPN connection (router to router).I want use PCANYWHERE to administrate a NT Server trought VPN.Which ports need to be permit to make this remote administration ?Is there any restriction ?Thank you for your response.

egrellet by Level 1
  • 964 Views
  • 2 replies
  • 0 Helpful votes

I've been tasked with looking at VPN Solutions for that will enable various offices to exchange information. We have a number of scenerios due to acquisition and I'm looking for some guidance, with some recommendations on the better solutions. I've n...

diagram is :2600(ce)--3640(pe)--7500(p)--ATM--7200(p)--3640(pe)--2600(ce), all connections is FastEthernet except 7500--ATM--7200.It can get vpn routes at the 2600(ce) routers, but ping can not go through the MPLS VPN Backbone. If diagram change to 3...

I have a PIX box that is doing NAT can I still establish remote user VPN's through the PIX? Where would I find PIX configuration info for this, online PIX doc's? Will the MS VPN client shipped with Win2k, or Win98 do this?

I have several routers in remote offices connecting through VPN with a central router, in a hub&spoke configuration, using IPSec.How can the remote offices communicate with each other securely, without fully meshing the VPN?Thank you!

rlitman by Level 1
  • 841 Views
  • 2 replies
  • 0 Helpful votes

Hi, At our company we have two 520 PIX Firewalls, 5.1(2) and 5.2(1) versions. I want a configuration with a VPN solution with them.Regards.

cwelhous by Level 1
  • 937 Views
  • 2 replies
  • 0 Helpful votes

Is it possible to have a VPN connection between a 515 and a 520, or do I need two PIX 520s?Thanks,i_lopez@tricom.com.do

i_lopez by Level 1
  • 751 Views
  • 1 replies
  • 0 Helpful votes

I have a few questions about VPN 3015:- for Win 9x/NT clients, could I just use IPSec; for Win 2K, L2TP is required?- if I have public IPs on both, outside & inside, is possible to give clients, from an internal pool a private IP range; do I have to ...

mionescu by Level 1
  • 822 Views
  • 1 replies
  • 0 Helpful votes

When I install the VPN 3000 client it causes the Windows 98 to boot up in safe mode. I have had this happen on three different machines. I have installed the client on several WIN 98 machines with no problems. I have tried updated windows, I have u...

In lay man's term what is the association between these two (MPLS and VPN Architure)and what are the strategic implications or advantages. Whats the future for both....