trying to add a new l2l vpn with the same config thats been deployed to many sites between asa 5505 (remote) and asa5550 (head end)
with this new one we are using a new type of broadband router and im seeing debug error:
Ignoring IKE SA (dst) ...
Hello,
I have a few of questions regarding a S2S VPN set up I'm being asked to complete. To give you some background, a vendor is requesting a many-to-one NAT from our 2 of our internal hosts to a single public IP address and wants to use this pub...
Hello,I need help connecting to a Site-To-Site VPN.Scenario:I have a Cisco 881 which I use as router/firewall.It is behind the router my ISP provides (FritzBox 3390).I want to establish a connection from my Cisco 881 to a client's VPN and only route ...
Hi ,
is it possible to have site to site vpn using asaB with below setup?
internal<->asaB(private ip) <--asaA-->(interface with public ip)<--->internet router<-- > internet<--> remote asa
pls kindly point me to any documentation if any. so far...
Dear All,
I am planning to use Cisco 5915 in one of the remote sites, the Cisco 5915 will be embedded in enclosure box, my question is that our network is based on IPsec over DMVPN with EIGRP, dose cisco 5915 support and what IOS I have found two
...
Hi , I have question over ipsec VPN access list to match traffic.I read that the access-list need to be in mirror condition to create Ipsec tunnel.I have point to multipoint scenario and I am using site to site VPN for every location.So my point is c...
Does any version of Software running on any ios or ios-xe routers (i.g 1941/ASR 1000) or an ASA (x series & traditional ASA) support the use of dynamic dns names for remote peer (IPsec tunnel) rather than traditional IP address?
I suppose that this...
Community,
I am noticing a partner (50.x.y.30) is sending multiple Phase 1 Requests to our VPN router (64.w.z.111) but cannot figure out why. Any idea what would cause this or how to fix it? All of our other VPN peers only show 1 Phase 1 setup.
I b...
[To admins :- Unsure why my previous post was removed as spam, i am reposting it. This is not spam]
Hello,
Pardon my limited knowledge. This has been passed to me.
We have a set of users trying to connect on anyconnect vpn as part of newly created ...
Hello There,
So I need to get voice working between 2 Hub sites that connect to HQ, so we have a VPN from site1 to HUB and a VPN from site 2 to HUB.. all good.
Now site 1 needs to make a call to site 2, site reaches the hub where the PBX is over th...
hi guys. I enabled securityk9 feature for IPSEC and the feature is in eval to use mode. After 4 or 5 weeks if I dont buy the license it will be go to right to use and permanent mode. My question is in this situation will the ipsec technology stop wor...
Getting an error while installing Cisco Anyconnect secure mobility client
"Failed to install AnyConnect Secure Mobility Client 3.1.02040 with installer error: Fatal error during installation. A VPN connection cannot be established."
Tried form di...
After setting up an Amazon VPN connection and configuring my gateway using the downloaded configuration, I am able to directly ssh to the private IP of an EC2 instance in my VPC. However, both the EC2 instance and an AppStream instance are unable to ...
Hi,
i got the business need that some users need an anyconnect session to another customer at the same time and this should be achieved with a terminal server.
So lets say User1 and User2 are connected to a terminal server at the same time.On thi...
Trying to install the anyconnect-win-2.5.2019-k9.pkg package on a Cisco 1811 router running c181x-advipservicesk9-mz.124-22.T5.bin, when I run the command in config mode "webvpn install svc flash:anyconnect-win-2.5.2019-k9.pkg" I get "SSLVPN Package ...
