Resolved! 5520 HA pair WLC with 3650 Stack switch
I want to build a HA pair with 5520 WLCs connecting them to a 3650 stack on two different LAG with trunk. Is this feasible?
Forum Posts
Hi, We are experiencing an interesting issue with our Wifi using 802.11x and our Radius Server. We have 2 AP (MR 16) with latest firmware that just stop sending Auth Messages to the Radius Server. All our other APs have no issues. The only way we can...
Hello, I've been trying to organize my network a little better.Some of the steps was to put WLC into my Equipment Management network. There is network:192.168.21.0/24 with Gateway 192.168.21.254. (Forigate) I put WLC Management interface 192.168.21.2...
Quiero iniciar un AP que me han dado en el trabajo pero cuando lo prendo me sale el siguiente ERROR y no puedo hacer nada/usr/sbin/capwapd: opening /click/wdog_helper/ap_monproc_capwapd failed!: No such file or directory/usr/sbin/capwapd: reading fil...
Have an odd problem we can't seem to figure out. In FlexConnect mode our clients (apple iPhones) can't seem to roam using 802.11r. The fast transition keeps timing out, and trying over and over to connect. This results in the phones losing wifi co...
We have clients that roam from building to building on our campus, and these clients maintain their same IP address with Mobile-IP. In certain situations however, the client will no longer have its traffic tunneled, and it will come over the subnet o...
i have 5520 cisco WIFI controller and the model of AP is AP1810W , it is working fine but if any access point goes down for any reason i can't see any alarm or log on the controller to identify which AP is down just i can know that the number of regi...
Hi to all, I recently puchase a new AP, model is AIR-AP1562E-E-K9.I think that it is a lightweight firmware, i see SwVer 8.3.111.0. cisco AIR-AP1562E-E-K9 ARMv7 Processor rev 1 (v7l) with 1030528/670976K bytes of memory. Processor board ID FCZ21XXXXX...
I have a Cisco WLC 2504 with the default QoS profiles defined (Wireless Section > QoS > Profiles). I have a WLAN tied to the Bronze (background) QoS profile. When I did a SPAN and Wireshark on my Cisco switch, I expected to see frames with the 802.1p...
Can you please advise which cisco solution for wifi is better for bigger office.I am looking to implement on two floors.ThanksSent from Cisco Technical Support iPhone App
I borrowed a 'Cisco SG300-10 10 port gigabit managed switch' from work to practice things i'm learning from my CCNA course. I have tried a serial to ethernet cable for console connection, and a regular ethernet cable from one of the ports. I have tri...
Hi, I am using Cisco packet tracer v 7.2.0.0226. I am using following topology. |LAP|------------(ethernet)--------------|3560 multilayer switch|-----------------(ethernet)---------------|WLC| As a start, I configured management IP address on WLC, c...
Resolved! Connecting (2) ANT-25's to an MR84
Can someone verify which is the correct method of installing (2) ANT-25's to a MR84?
Cat3560CX >>>>>> WLC2504 >>>>>> AP3602i gi0/x Trunk LAN1 LAN4 PoE LAN I have a VLANx (10.x.x.0/24) for infrastructure configured on the Cat3560.I have an AD server configured wit...
Every device are connect to SSID but one device not connect. 802.1X in use this SSID. Debug logs are here: *IPv6_Msg_Task: Sep 02 06:09:27.837: b4:9c:df:4b:f0:f7 Link Local address fe80::467:6bd4:8946:e838 updated to mscb. Not Advancing pem state.Cur...
