Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi all,Running 8.8.111.0 on an 1850 Series, with 6 SSIDs configured, I'm not able to disable the FASTLANE option by Web-GUI.In the GUI I can select disable for the FASTLANE option and apply the settings. But entering the WLAN-setting again, the optio...
Hi all, I have to setup several new Wifi environments with a lot of APs and 3504s. All APs should work in FlexConnect Mode. When I connect a new AP to the network the whole config comes from the controller except FlexConnect mode. So I have to config...
Hello. I need help. Right now I have a cisco WLC working with ISE. Right now users using mobile/laptop when they want to authenticate, they just need to input their username and password after clicking the SSID (using 802.1x authentication).Now, my c...
Hello,we are facing issues with an ap mounted 15m high in ceiling in one of the warehouse. Model is 2700 E and checked the power level of both 2.4 and 5G, both are at high power since there are no near by aps. But still we are getting signal only fro...
I tried to join new AP1830 on 1830 WLC - mobility express error AC rejected join request[17], try again later. please help thank you
Hello Experts, PMF appears to be an important feature that we needs to enable on a WLAN which is wpa2-psk or dot1x capable. However it does not has any mention in the configuration recommended practices. Are there any known issues of having them e...
I may be missing this but some how all the AP's on one of my controllers are set to "AP Specific" rather then "Global Config" for the telnet and ssh access for the AP's on the Advanced tab. Is there a way to "bulk" change this config to "Global Confi...
Hi, I am facing issue in cisco prime up-gradation from 2.2 to 3.0. Facing error while loading file through FTP server (i.e) Link error. Anyone please help on this.
1242AG aps on 4400 controllers, running on version 7.0.116.0 & 7.0.252.0. Clients dont connect to 5G even if we have bandselect enabled. Checked network status of 802.11a, it is enabled. All clients on 2.4G only. Any suggestions?
All access point connect to wlc and all services run fine but access point can’t ping from wlc also client is not ping able from wlc
I'm looking into Meraki's built in 802.1x authentication and was wondering if there is a way to create groups and assign Vlans to specific groups of users. I know with Meraki's built in authentication, you'll need to create a login account for each u...
Hi all,I have a few questions regarding WLCs and CAPs.1) On my CAP2602i I can see a "primary software version" and an "IOS version" installed. Whats the difference?2) If I want to upgrade my CAPs to a newer version, I can only do this via the connect...
Hello All,Could anybody tell me how to configure 300 AP(s) in the same network with WLC 3504. I know that WLC 3504 supports 150 AP(s). So i need 2 WLC 3504. How do I configure all the 300 AP(s) in the same network?
In the middle of total boredome we spent hours with the new unprimed universal access points (AIR-AP3702I-UXK9) combined with some of the attractively priced mobility bundles... SCENARIO: If you just use the unprimed AP and connect it, it joins the c...
Hello, I am configuring an autonomous AP 2700i but this an UX one... and I've read it's not possible to prime an autonomous AP but only a lightweight one. Your advise ? Can I convert it to lightweight, prime it and convert it back to autonomous ? ...
