Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello, Is there any chance of using Cisco vWLC 8.5 without CMX and retrieve device/client location data to an external server?Basically we want to have an external server that receives data about users locations, etc.We found a "Server" configuration...
Good day,My query is as follows, which Access Point outside without contemplating the 1552, has standard to be used in a Gas and Oil Factory (intrinsic), or that has standard ATeX and CSA. Regards
I have the following problem, I have 2 WLC 5520 in HA, with Access Point 2702i and 2802E, of which the APs 2802E are always kept at the maximum power, and APs that are side by side are in the same channel, being much co-channel interference. The OS v...
1552H Mesh network (3 RAP, 13 MAP, 2504, Outdoor) dropped after 10 days working. Checked with WLC, 5GHz radio are down. RF2 LED of each RAP is off. Tried rebooting WLC and mesh was up for a while but drop again at the end. Only 3 RAP found in WLC.Cou...
I habe moblity express 1815 8.8.100 and one acces point 8.3.111 i would AP joind to controlleur i need to help
Hello,On Cisco WAP571, there is no SHA support and no AES support for SNMPv3 even on the last software version 1.1.0.3.Only MD5 and DES is available.When SHA and AES will be supported for SNMPv3 on Cisco Small Business wireless access points ?Thanks
We in the transition phase of replacing EOL Cisco AP's(WLC managed) to Cisco Meraki cloud AP's. This transition of Cisco Aironet ( WLC managed)APs to Cisco Meraki will be in multiple phases based on the aging and EOL status .During the transition pe...
Hi, So I'm fiddling with a 5508 with a bunch of 2802 access points connected and when I'm looking at the Access points-> 802.11b/g/n settings I see a lot of "Client Serving * (Local)" and "Client Serving * (Remote)". I've read some other post on thes...
Hello,I have joined the company where most of the wireless network was done by third-party company long time before I joined.Would really like to know a bit more about the setup, and how to make it! Currently:Each room has 1810W, with Cisco phone con...
Hello Experts, I need to run two Prime HA pairs in my network. Additionally I need to have one operations center in HA to monitor those two instances of Prime HA. In the ordering guide, I just don't see the mention of HA license for operation cent...
Hello,We have a warehouse remote site, with 27 3702 APs, a remote flexconnect WLC 5520 (with local switching). APs are powered in medium power by CE500 switches POE ports (15.4W)Scanners were facing some disconnections and slowness. We decided to imp...
Hi - we have deployed a vWLC 8.8.120.0 for testing because we wanted to use AVC to correctly mark voice traffic from Microsoft Teams (we needed a minimum protocol pack 37.0 to detect it correctly). After deploying the OVA into VmWare and accessing t...
Resolved! VPN from Meraki guest wifi
Hi,Got a question about VPN from the Meraki guest wifiWe get a lot of different vendors in the building, who almost all use VPN to connect back to their respective motherships, however, with the Meraki guest wifi they are unable to get access. My cur...
Hello, I am working now a days on Cisco Access Points, as you already know there are different products are available but what i don't understand is each model for example AIR-CAPXXXX-A or AIR-CAPXXXX-E or AIR-CAPXXXX-Kwhat does A, E, K mean? Thank y...
We currently have Flexconnect Local Switching configured at 2 of our three offices and we're using ISE for our CWA for the internal network SSIDs. We're about to stand up FCLS APs at our third office (Site C in the diagram) and we don't have a contro...
