I have a customer that want their clients to transmit at 10mW only. Is it possible to configure client tx power from the WLC?
I have a customer that want their clients to transmit at 10mW only. Is it possible to configure client tx power from the WLC?
HI, I am looking for an autonomous Cisco AP. and found this link http://www.cisco.com/c/en/us/products/wireless/buyers-guide.html#~indoorac-wave1. from here i can see 3700 and 2700 support autonomous mode. however in Cisco support forum, some are di...
hello, could you please let me know if this item AIR-ANT2524DB-R= is end of life? if yes, what the replacement part? thank you
Hi, I have a huge problem with my partner - we displaced our password list! Is there a way to reset the access point, without entering the GUI? Any help is appreciated a lot!! Otherwise we will have to take it to the service... Thanks
Hi all, I just wanted to get the opinion of those who have "been there/done that" when it comes to centrally switching vs locally switching wlans. I will give as much info as i can on our wireless network design. This is for a school district with 25...
I've 2 WLCs 7510 in redundant mode and I need to dismount my redindancy because I need to convert my HA unit to a full independent WLC. Can you tell me how to do it please? I need to connect 300 APs when converted. Thanks, Ferran
Hello all, I followed the cisco procedure to go from lightweight to autonomous AP. I configured HTTP access with ip http server. I cannot log in into the AP GUI cause the AP keeps on saying AP is not in Flex connect mode (and keeps on looking via DH...
I have two WLC 2504 one as Active and the other are HA .so the installation will be N+1 .and also we have to switches 4500 using HSRP between them . i need what is the recommended design for connect both WLC to the Two cores . is the attached diagra...
Hi we migrated a customer from standalone APs to Cisco WLC (8.1). He has some devices that worked only in standalone mode, when we activated "subscriber-loop-control" on the bridge group of the wireless subinterface. When we then migrated to WLC ...
How can i up-gradate my cisco asa 5525 ips module.Please give me the step by step procedure.
Hi guys, I have a Cisco Linksys E1200 router. I'm trying to use this router as an access point. I've followed p.36 of this manual: http://downloads.linksys.com/downloads/userguide/E_Series_UG_E900Rev_3425-01486_Web.pdf which, in point 4, says to find...
The Ap 1830 can support up to how many VLAN 's ?
Dear Support, we got several WAP 351 for the forklift vehicles to connect several ip cameras and rugged PC.the idea works fine with AP1240, but we faced with several issues like additional switch requirements and connection speed limited at 54mb/s po...
Hi Experts , I m having an issue to join AP to WLC and below is the error.. Mar 1 00:02:03.479: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL LER.BRCCVADS.COM From console AP,I m able to ping GW and WLC IP but when join,its fail... P...
I have (6) sites connected over Microwave. I need to replace existing 6500 switches to smaller form factor switches at each site that connect to Microwave device at each site over a Multimode Fiber. Those switches will support internal users at eac...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-12-2024 05:27 AM | ||
04-10-2024 01:01 PM | ||
04-05-2024 06:44 PM | ||
04-04-2024 03:18 AM | ||
03-27-2024 07:38 AM |
User | Count |
---|---|
15 | |
5 | |
3 | |
2 | |
2 |