Hello Guys, I have a Wlc and I have just added a new outdoor AP 1532I-E-K9 and I have seen that this model doesn't works in the U-NNI 1 channels My question is: what kind of Cisco AP model can works in the U-NNI1 channels but in an indoor room with...
Forum Posts
We have updated our customer wireless network with new 1562I and 1562D access points. We have diverse clients that wok fine, but we are facing some connection problems with third party clients used as wgb, wlc fail to comunicate randmly and shows err...
Resolved! issue with NPS server and Bridge Groups
We have a Ubiquiti setup and an AP has started giving us trouble. Decided to put a Cisco in it's place. We currently have 2 SSID on different VLANs and 1 Management VLAN. A Windows Server 2012 R2 Box acts as the NPS server. It has a nic on VLAN 10 a...
Hi! I'm wanting to take the CCNA Wireless exams (I've actually got about 15 years of WiFi experience, but the last Cisco AP/BRs I've used were the ancient Aironet 350s. I used tons of equipment from other vendors). Since I like practicing at h...
Resolved! Aironet 1852e - Antenna doubt
Hi, I bought some Aironet 1852e without antennas. The deployment will be done using only the 2.4GHz band due I'm not planning to use 5.8GHz. I have a lot of old AIR-ANT2422DG-R antennas (2.4GHz only) so I would like to know if this antenna model is c...
I have registered Tecom dmp330 wifi-phone like a 3rd party sip device to CUCM 7.1.5 So it works fine with outgoing calls, but not works with incoming calls. When I take a call nobody hears each other, but if I hold on this call and then retrieve it...
Hi I have some questions about a wireless setup. I have a wireless lan controller 2504 and have two wireless cisco 1562's The Wireless Lan controller is on firmware 8.5 along with the WAPs. I will be connecting the WAPs, one as a RootAP and the o...
Dear Friend, We wanted to purchase 5 Access Point for my one of client for small office but high priority setup. Access Point should be stand alone and have (mobility function) when you move from one location to another location, system automatically...
Hi Guys, I am currently trying to setup a MESH toplogy involving 2 x 1562E outdoor APs, 1 WLC 3504 and 2.4Ghz Omnis and 5Ghz directional antennas. The issue I am having is when configuring the Antenna Band Mode from "Dual" to "Single" From the...
We are designing an AP placement plan for a large hospital that will have requirements for high density and location services for an RTLS solution. We are planning on using the 3800 series AP. The RTLS solution operates on 2.4GHz only--obviously th...
Hello Experts, I am configuring MSE HA through Prime. Prime is with code 3.4 and MSE with 8.0.110.10. The problem is the HA pair is just not happening and struck at 79% for almost 3 days. Is there a known issue for this? How can we have this go...
So i just work as NE for two weeks with zero experience in AP and WLC (I have CCNA R&S). I have learned our company WLC via web GUI, and know a little bit about how to see active clent and its mac address, our APs, SSID, WLAN and basic stuff. But the...
I have two Cisco Aironet 1815I running mobility express. I've created two SSIDs, one for guests and one for employees. I've seperated them in AP groups so one AP is responsible for Guests and one for Employees. The controller is running on the AP wit...
Resolved! MA-ANT-25 connection to an AP MR-74
I guys, hope you are fine.I've a MA-ANT-25 to install in an AP MR-74.The antenna is dual band, so I can connect one connector to a one radio (2.4Ghz) and the other connector to the other radio (5Ghz), or I've to connect the 2 connectores of the anten...
