Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Good dayI need to find a system that can simulate wireless network.I use packet tracer it does not meet my needs, the device is very small and does not have enough featuresThanks
Hello Cisco-WLAN-Community,I would like to report a WLAN-AP-Join-Problem that arised here during SW-Upgrade on 9800-80-WLC to version 17.9.5.Despite the fact, that this hospital is running a HA-SSO-9800-solution, more than 1200 APs were no longer abl...
For a meshing solutions I've been breaking my head over a question and I can't find the answer via searching, so I'm hoping someone here can tell me the answer. Assumptions, correct me if I assumed wrong: 5 GHz is used for backhaul for less risk of i...
I have upgraded Firmware of WLC (Later than ver8.5), restarting WLC for re-assignment of IPs via DHCP, and resetting AP doesn’t resolve the issue.I have tried to1. Check for Basic Connectivity (Ensure that the AP is powered on, Check the cable connec...
We have deployed a C9800-80 controller in HA and are using Catalyst Center to provision the controller telemetry settings, netflow, to use the device management port, Gi0, and it is not being sent. We also attempted to use the AP management port, Te...
I would like to implement a guest access solution for my wireless clients, where each guest is assigned a unique, automatically generated username and password. Ideally, this would function similarly to a sponsored portal or lobby-based authenticatio...
I have three access points in my office that I've been using SSH to get into the CLI. I can't get into the GUI though using a web browser. There's a lot of old forum posts that I've tried to follow but almost no commands are available on my machines....
Testing out one of them CW9178Is and noticed that the SSID will not broadcast if you disable all but the 6Ghz radio. Can anyone else confirm this?-802.11be on/off-AFC on/off-Manually set different channels, widths and power
HiI have 3 APs connected to a 9800-CL controller. they are installed in a line along a large hallway. After a reboot everthing works well, clients connect to the nearest AP.After a while clients dont conenct anymore to one clients and after some more...
Hi Team, I'm facing a problem the AP not joined the WLC, please find the logs below. [*01/27/2025 12:49:29.9297] CAPWAP State: DTLS Teardown[*01/27/2025 12:49:30.9777] OOBImageDnld: Do common error handler for OOB image download..[*01/27/2025 12:49:3...
I'm trying to get AFC working on my 9800-40 but it doesn't seem to be able to communicate with the Cisco back end. What URLs or IPs do we need to allow through the firewall to allow this to work? I don't think our management vlan has any outside in...
I'm having a problem having mDNS to work in my environment. I searched diligently online, reddit and this forum to see if I could find a similar post or solution to no avail. If someone can help with with a solution to this issue it will be greatly a...
For our guest network, we have a C9800-40 WLC acting as a foreign controller, and a C9800L acting as an anchor controller. The anchor is in our DMZ and helps keep the guest network completely segregated from our internal network. Currently, we have a...
In the WLC we can contain the Rouge AP, but how we can make sure our AP is not contained by neighbor WLC if the my AP located not to far with neighbor AP?
Model Name: DN2-HW-APL/ C9800-40 Software Version: 2.3.5.4-70852-HF3 ■Inquiry Contents In an SDA network environment, if you mix C9105 and C9115 access points, Are there any problems with wireless operation or Assurance? For C9120, the Deployment G...
