Wireless

Mar  1 18:44:10 wlc.sup46 Cisco_ac: <mac>: *Dot1x_NW_MsgTask_0: Mar 01 17:44:05.667: %PEM-6-QVLAN_INTF_REMAP: pem_api.c:1836 Remapping interface ID for <mac> from 12 to 13 (ifname). Mar  1 18:44:12 wlc.sup46 Cisco_ac: <mac>: *DHCP Socket Task: Mar 01...

We have a new Data Centre with a new ISP design. I have 4 x 5500 WLC's:- 2 x Anchor Controllers sit on the DMZ one in each Data Centre 2 x Foreign Controllers (one as Primary Master Controller these manage the internal AP's) Between each Data Centre ...

As I can connect HA the wireless controller and each access point can log in to the ip of the city that is connected, I mean the access point of the city one connected to the city's two but has the same IP assigned the city one , It is possible to ma...

I was trying yesterday to pair two units of WAP571E using bridge option at wireless menu. Succesfully at 2,4 GHz, with full strenght receiving signal, but if I try to scan 5GHz signals at Rogue AP Detection option, no signal is detected. I try to sca...

Hi, I would like to know the difference between these two part numbers:- AIR-CAP27IBO-A-K9- AIR-CAP2702I-A-K9 Thanks a lot. Regards,Ivan

Hi Experts, Thanks in advance... Recently i am facing Limited or No connectivity problem among my windows AD users, who all are authenticated using Radius for wireless access. problem could be for 10 to 15 second but all VPN, Internet, RDP connection...

Hi! I have an issue with my WLC2504 box. After some manipulation of the box : - I cannot reset the config : it comes back to the config I had set in - I cannot use the Console port any longer (?)  - the only way to access the console mode I have, is ...

HI Team, We have a foreign/anchor setup with three WLANs Corpnet- For internal users Devicenet- For BYOD Guestnet- For Guest users What we want to achieve is to change the profile settings so that all DeviceNet/GuestNet traffic to de-prioritised in (...

hi, i need to deploy 2x APs for a small site. my questions are: 1) if i deploy these APs for mobility express, do i only need 1x AIR-AP1851E-x-K9C to act as WLC and AIR-AP1852E-x-K9 as subordinate AP? or do i need both to be as AIR-AP1851E-x-K9C? if ...

Good evening guys, I have my enterprise wlan thru controllers. for collaboration I need an SSID that just use WPA2 and connect devices such as Epson smart tv, smart board, etc and another SSID in the same vlan to students to connect and get thru the ...

Hello,just a question, what happens if you install single band antennas onto dual band ap connectors, would it work?greetsJ.

I have a site that are using Cisco 3850 switches with Cisco 3802I access points, and a 5520 WLC. It appears that the capwap message is being blocked by the switch.

From the OEAP600 literature here:  http://www.cisco.com/c/en/us/support/docs/wireless/aironet-600-series-officeextend-access-point/113003-office-extend-config-00.html While there is only one physical port on the device, up to four wired clients can b...

Hi,    I have controller and the access point are on the subnet. Due to some requirement i want to statically add the access point ip address and controller ip address into the AP. Kindly suggest me the suitable commands for this. i used the followin...

It was GUI upgrade of our controller WLC2504 with software version 7.4 First of all I downloaded software image AIR-CT2500-K9-8-0-140-0.aes via GUI. All checks were ok. Then there were two basic steps 1) "Reboot" 2) "Save and Reboot". Ok, It's gonna ...