Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! HA between 5508 and 5520 WLC
Hi all,Can be possible configure HA (BOXTOBOX) between WLC 5520 and wlc 5508 ? any help apreciated.
Resolved! QoS on wlc and Ap
Hi all,who can help me to solve my question :1 - Can wlc or AP Cisco support 802.1p ?2 - Can wlc and ap classify and assign priority and a bandwdith on particular protocol ?3 - Can wlc ad AP support traffic shaping ? any help apreciated.
Can I config webauthe redirect without httpsI try to config for force to http://1.1.1.1but It still redirect to https://1.1.1.1 Here is CLIparameter-map type webauth global type webauth virtual-ip ipv4 1.1.1.1 redirect for-login http://1.1.1.1 redir...
Hello, We have two 5508 WLC's in HA mode with a 125-AP license. Recently we had an "Active controller failed" scenario. Of the 98 AP's on our primary WLC, only 65 failed over. Any thoughts as to why the other 33 would not have failed over? Were on WL...
Resolved! WLC 2504 - Configure a backup unit
I have set up a WLC 2504. all working well.I now need to configure a secondary unit, in case the primary ever fails, I am using the express set up and have configured a different managment IP,but how can I get the config accross from the other unit? ...
Resolved! Configuring PAT on 881-W access point
I have a Cisco 881-W router with a built in access point.The Fa4 WAN interface connects to the provider on a pubic /30 point-to-point.The Fa0-3 LAN interfaces and the built in wireless access-point service an internal 192.168.1.0/24 network through D...
We are a mobile development team from Nable AMEA. We had Schedule the Cisco Connected Mobile Experiences Connect v1, from dCloud. We are developing a mobile application software using the CMX-MSE and we are facing two problems. First problem: I...
Hi, we have 3 of these aironet 1602i-e along with other access points that provide wifi.I am not the person who put this up, and am taking over from a previous person so I don't know how the initial configuration was made but I was looking at these a...
Is the command: "config redundancy link-encryption" only available in a ldpe image? Or is there a prerequisite command that needs to be applied first before the command is available? In a normal 5508 image, that command is no where to be found.Than...
Hi there.After setting the firewall up, I now need to configure the WLAN.According to the manual the interface is getting 192.168.10.2, but I can't reach it.The interface is enabled, with ip 192.168.10.1 and the wlan module is enabled as well. Can an...
Hi! My main issue:I want to be able to get the accounting radius info to several firewalls from the same SSID. As of now we have one 5508 (sw 7.6.130.0) controller that has APs on 5 physical locations where 4 of the locations are connected with site ...
Dears,Urgent.Need Assistance to configured the Cisco Aironet CAP2202E -E -k9 for bridging Mode.
Hello, I have a 2500 Series Wireless controller. I have everything configured and have 2 AP working right now. But i need to know how to enable the 5GHZ settings on it to connect through the 5 and 2.4. Thank you for your help in advance.
I have 5 APs on my network being controlled by a 2500 controller. I need to add another AP. Can I add a second 2500 controller for additional APs?
Hello folks,I really feel sorry for bringing up this discussion again. I wouldn't dare to ask this question if I find someone's clear cut suggestion/solution or an overview giving a detailed step-by-step procedure. People just suggest jumping through...
