Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Cisco 5508 + Local Authentication
All,I currently have a Cisco 5508 WLAN Controller with multiple SSIDs setup to use 802.1x with ISE for authentication.I would like to add a new SSID to the 5508 and have it set to use local authentication only.I have checked the Cisco documentation o...
Guysi am having wlc(5508) running with 7.0.220.0 and i am trying to upgrade to recent one 7.6.110.xwht are nearest release i need upgrade before i ugrade wlc to 7.6.x.x?any URL with refernce to this?which is recommnaded recent code?Thanks
Hi, I'm testing out a vWLC and have set up 4 APs all in FlexConnect, the Controller is at my central site and the APs are located in Branches across countries. Everything is working fine except for this one AP which keeps rebooting. (1602 series).So ...
How can one restore a backup from Prime 2.2.1 to a replaced WLC 2504 that has minimal configurations and am able to get into it remotely GUI and SSH?I see the RAW configurations but it looks like "config" needs to be added to each of the many lines.A...
Does anyone know of a report in Cisco Prime Infrastructure that would provide a count of all alarms of a specific type for a specified interval of time, such as disassociated APs for the past week? It seems the only thing that comes close is the AP i...
Where can I find "unknown devices" in Cisco PI 2.2 under the converged view like I can in the classic view?
I have a customer who is telling me that they are using Windows phones and they need PKC turned off.We are using WPA2 - which seems to me turns on PKC automatically.Is there anyway I can turn this off ?If so where ? I have been all over the controlle...
Resolved! CISCO MSE web service port configuration
Hi,I recently configured CISCO 3310 box with MSE version 7.2. Services are up and running in the box, I could add the MSE to WCS and also able to track the location using WCS. However, I could not connect the third party software to MSE web services ...
Hello, I am new on Cisco area and I would like to take data from a Cisco wireless controller(If it is possible). I little confused where to look and where to read and how to communicate with Cisco machines(I use Java). I would like to guide me where ...
Dear Expert,The Catalyst 3850 be able to connect Access Point.I checked the CCO, but I don't know to connect the Access point directly or indirectly...Does it must connect the Access Point to the Catalyst 3850 directly ?Could you let me know about Ca...
Hello, I have Cisco WLC 5508 configured with one SSID taged to one VLAN. Post connecting wifi, general internet is working fine for all users. But, communication between clients in the same vlan it is not happening. Controller model: 5508AP: AIR-CA...
Hi Guys,We have around 75 Laptops, and we must migrate from SSID A with WEP to SSID B with WPA2/.1X.I have enabled B since a week or so, to run in parallel with A, The Server Team reconfigured the AD Group Policy for all PCs so that their primary SSI...
All, I have been trying to find a solution revolving around getting a Mobile Xray unit on the wireless network. Our first attempt was to use a small business RV180W to create a bridge. It appears this may not work as all the APs are using LWAPP. We n...
Hi,On the business, we have 4 access point WAP371 Wireless AC/N Dual Radio Access point with single point setup.Firmware Version (Active Image): 1.2.0.2Firmware Version (Non-active): 1.1.2.3Connected to Cisco switch SG300-10PPAll working good except ...
Hello probably a beginner's question but how can the 8510 controller support 6000 APs in centralized mode when it only has 10Gbps while the 5520 supports 1500 Aps only and has 20 Gbps ?
