Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
I configured P2P blocking with Flex Connect mode . Client in same Aps is work but client in difference Aps still send traffic between client. Can you give me any idea to help to troubleshoot this issue? Regards. Wongsakorn.
Hello all, I'm having a problem with the Download Software Tasks in my Cisco Prime 3.0.0.0.78. I've always updated my WLC's via Cisco Prime, during the night with this feature. I create a download software task, in Configuration / Templates / Schedul...
Hey everyone, I have this question, does anyone know how much time it typically takes to transition on the same SSID but between 2.4 and 5.0 spectrum? Essentially i have clients that in certain areas of the floor are associated on the SSID on the 2.4...
Hello, Is an adder license tied to the serial number of the WLC and cannot be installed to a different WLC? We needed to add more APs but we have reached the limit of 5. Thank you! Cisco 2500 Series Wireless Controller Software version 7.2.111.3
Good afternoon, I have an outdoor AP 1572 connected to an AIR-ANT2513P4M-N= antenna. The access point is powered using POE that connects to a SB SG300 switch. I configured the Access Point to autonomous, with Version 15.3(3)JC. The problem is that wh...
In order to test CCX Radio Measurements (S36) one is required to enter a "hidden" test command into the CLI of an access point: test aprm mreq client .....as per Appendix K of the CCX Test Plan 1-4.This should force the access point to generate a mea...
Hi Folks, I'm having troubles with a wireless installation root / non root Bridge using autonomous AP. The issue is that as soon as I enable encryption the connection is gone. Without encryption everything is working fine. I've attached the configs -...
Hi, All the AP's connected to this WLC AIR-CT2504-K9 went down and again came up without any reason. The only reason is could see is 'Reason: Capwap WTP Event request'/'Reason: Capwap Echo request' . But this doesn't explain why all AP's got disconne...
Hello, I have Cisco 5508 Wireless Controller with software version : 7.2.110.0 I bought Cisco AP 3700 series. I checked Cisco APs required controller software version 7.6 or later to work. By any chance can I upgrade the controller software to work...
hi all, I encounter something strange lately. for Iphone device - only for Iphone, it needed some time to recover the connection to the internet. I can't find anything in the logs why it reacted this way. The iphone lost connection needed a while t...
Hi Regarding Native vlan in 6500 series switch for wisim-1 module there is compulsary native vlanxx for Registering for Acess pointslikeSup720(config)# interface range GigabitEthernet3/5-8Sup720(config-if)# switchportSup720(config-if)# switchport tru...
I have 3 1852 access points. I have attempted to configure a couple of them as a controller. I have verified the software, 8.2.100. Show version shows: AP Image type : MOBILITY EXPRESS IMAGE AP Configuration : MOBILITY EXPRESS CAPABLE I run the co...
Does Cisco make a signal booster product? I need an office setup with wireless access, but i can not run ethernet cable to the office. One floor below and down the hallway i have a Cisco access point, but the signal is 2 weak 2 reach the office that ...
Hi, While roaming the station shows no signal (lets say -80 to -84 ) bar but still seems it's connected . does it indicate the coverage gap ? Thanks
Hi guys I found 2 related docs about wireless vlan assign with single SSID, but my question is what happened if ACS/Radius server down or authentication fails. In wired 802.1x situation we could define failure vlan and guest vlan, but I didn'...
