Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello all first I'd like to admit I'm not a Cisco guru at all I have limited knowledge of Cisco devices but a customer of ours has a Model 5508 Wireless Controller and he's having an issue with it receiving requests from there DHCP server. Also if th...
Hi, I am configuring a Wireless network spread over 8 sites. The core site has a DHCP server, but the customer would like to use DHCP at each site for the individual DHCP requests from that sites wireless users. Is it possible to do that? I only see ...
Hi everyone.In our office we have a problem with Cisco WLC 2504 and 5 Cisco AIR-CAP2602. Everything works very good for some time, but after half an hour after connection starting problems - speed going down, and latency became very high, also wi-fi ...
Hi,I have a Cisco AIR-LAP1262N-E-9 but I cannot access via console and GUI. Also, I noticed that after getting IP address from DHCP server, its IP address will be released after 2minutes. Then after a while, the access point will get another new IP a...
Resolved! Cisco 2602i Autonomous Mode
Hello,I am having a simple issue associating to my stand alone Cisco 2702. Debug displays the following output:*Mar 1 02:07:50.471: 3D75990E r 5 29/34/39/37 63- B000 07F 69E300 D168DC 69E300 F0D0 auth l 17 algorithm 0 sequence 1 ...
Hi,We have two Cisco 2602i devices installed in our network and around 90+ users are simultaneously connected over the network. In order to tighten the network with loop holes need to configure some features on these standalone devices.1. Configure W...
Resolved! Assign Vlan to SSID
I have a few Cisco 1141n that are stand alone AP's that have one SSID on them. I would like to assign the ssid to vlan 2 but also be able to keep the native vlan 1 as a trunk port on it for snmp graphing as well as management of the ap. My router is ...
HelloDoes any one have infromation what features will be implemnetd in WLC release 8.0 coming soon?I like to get release notes and PPT ..
I realize this is probably asked and answered 50,000 times.I have some new Cisco 2700 series access points coming in for this site and will be deploying at other sites.Does anyone have a simplified document on how to configure 2008 R2 with RADIUS or ...
HelloI have a controller 5508 running on version 7.4.121.0. With the command "show ap config global" I can check the global AP syslog config:AP global system logging host.................... 0.0.0.0AP global system logging level................... in...
HelloI have a WC5508, base license, Image version 6.0.199.4. I need to upgrade it to 7.4.100 to support new AP 1600 serise. Can I upgrade it to 7.4.100 directly, I understand I will lose Vlan mapping on H-REAP settings, but that's OK, I can redo tha...
Hi all, I faced a problem in my WISM2 in 6500 when I issue the command of #show WISM status I found that the status of the wism is "Started KeepAlive "not operational please advice if there is a solution except that I reload the WISM.
I am running Cisco Prime Infrastructure (2.1) that manages a Cisco 5508 WLC (7.6). We have multiple version of AP's managed by this WLC to include 1142, 2602, 3702, etc...In Cisco prime when we run a Rogue AP Report. None of the Rogue AP's discovered...
I am trying to get a Symbol MC9060G with a new 2602e AP that is a stand-alone. I have configured the AP for WPA-TKIP with a PSK and it works fine on a laptop. The laptop can use this same profile on the old AP as well as this Cisco 2602e. The scann...
Dear ALL,Kindly give your feed back Does Cisco AP 1600 15.2(2))JB2 supports WLC AIR-CT2504-K9 ver 7.0.220.0 ?highly appreciate your kind response... regards
