Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi team,I am not familiar with tag in Meraki access points, have many access point in our organization. most of the access points are tagged like - printer, floor 8, 9 something likewise.Can anyone explain what the use of tag and in which scenario we...
Resolved! AP Join issues for select APs
I have an existing 5508 with about 400 APs that has been in place and working well for many years. I am in the process of adding a few new APs and I've had a problem with joining some of them. Out of about 20 APs, about 5 of them have problems join...
Experts, seeking your support in the following issue. Requirement : Convert the AP 9115 AX into EWC, However there is an issue we faced while uploading the EWC image using the "ap-type ewc-ap " using TFTP command Test Setup: Laptop installed with TFT...
Resolved! Unable to convert Cat 9105 to EWC
I'm trying to convert a 9105AXI to an EWC, but I don't have ap-type ewc command, which the documentation at https://www.cisco.com/c/en/us/support/docs/wireless/embedded-wireless-controller-on-catalyst-access-points/215303-embedded-wireless-controller...
Hi,I would like to seek from anyone advise about the licensing in Cisco C9800 WLC controller how's it work actually?As I have found that the license not activated in my current Cisco C9800 WLC controller past two days ago, this incident happened when...
Hello Everyone,I’m working with a Meraki ecosystem, specifically using the MR57 model. We typically project our laptop screens onto a Samsung TV using the Windows + K shortcut. This works most of the time, but it’s not always stable.Occasionally, the...
Resolved! Wireless - 802.1x auth fail
Hi, let me see if anyone saw a situation like this:802.1x PEAP MSCHAPv2 authentication using a laptop windows and a smartphone.The Radius Server is Cisco ISE and it reply the MR AP with a Access-Accept packet.Cisco ISE and Access Point are connected ...
Do these dual ethernet AP's allow for ethernet OUT to addtional AP's or networking?i guess my question is can they act like a 2 port switch?
I've noticed the Meraki DHCP (Nat Mode) states "Clients receive IP addresses in an isolated 10.0.0.0/8 network. Clients cannot communicate with each other, but they may communicate with devices on the wired LAN if the SSID firewall settings permit." ...
How to assign primary/secondary/teritiary controller in ap ?Is it done manually on AP or different process.
Hello all,I'm setting up a new Catalyst 9115AXI-B with an embedded wireless controller C9800 and am having some trouble getting my wireless clients to get any DHCP information from my external DHCP server. The server is a Windows Server 2019 domain c...
My Ap's are suddenly getting Disabled gateway (Bad IP assignment) throughout the day. These were installed over a year ago and never had a problem with their configuration before. they are Mr56. Firmware: MR 30.6
Hallo,ich bin neu hier und benötige eine kleine Information.In meinem Heimnetzwerk mit einer Fritzbox 5530 verwendeich aktuell einen AP von Cisco ( 145 AC ). Da ich nun das Netzwerkum ein paar WLAN-Kameras erweitern möchte, will ich diesen eineigenes...
As the title says, after upgrading to version 17.12.03 all APs (c9115AXI-B) in a remote office are looking to be en a constant boot loop and the error message shown is "DTLS close alert from peer". This is strange as it is just this one remote offic...
Hi all;As far as I know, to disable AP Failover Priority functionality in AireOS-based WLCs, you can use the "config network ap-priority" command. Right? Now, Is it possible to achieve the same functionality in Catalyst 9800?Another question is that,...
