Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello: We want to add some 1815i APs to an old WLC deployment. We're only able to find new 1815i autonomous (K9) but we need lightweight ones 1815i (K9C). We know that we can use the recovery image for convert autonomous to capwap, but in the drivers...
I have accidently removed partition 1 & 2 during the uboot.Now the AP boot loop with below.____ _/ ___|(_) ___ ___ ___| | | |/ __| / __|/ _ \| |___ | |\__ \| (__| (_) |\____||_||___/ \___|\___/_ _ ____ _| | | | | __ ) ___ ___ | |_| | | |___| _ \ / _ ...
I'm using a few Cisco Aironet 1142 ap's in my house configured with autonomous images.The firmware version I have is c1140-k9w7-xx.153-3.JD17.The problem I am running into is there is nothing at all under Network Interfaces on 3 of these ap's.One sho...
In a Cisco Catalyst Controller 9800 SSO deployment, will failover occur if the interface or port-channel of the active WLC is physically shut down?
Hello,AP for branch office registered to the WLC in Main Office, and the AP using flex connect mode.If we see in below picture, VLAN 250, 118, 124, 117, 131 is not exist in the Main Office, only VLAN management 303 exist in the main office.With this ...
How Data traffic will be done between AP and Controller ? Is it go through CAPWAP, I believe CAPWAP used to both control plane and data plane ?
Hello colleagues,I'm running Embedded Wireless Controller 17.12.03 on C9115AXI and having issues with this config:ap profile default-ap-profile description "default ap profile" mgmtuser username admin password 0 Admin,12345 secret 0 Admin,12345 ntp i...
Hi Alli'm looking for help and some instructions on how to setup a Home Mesh using 4 x Air-CAP3702i-e-k9 , i do not have a controller on hand , and will be using a Normal POE Injector to power the units up , is there a possible post of guidance on h...
Hey,I’m having issues recovering my Cisco Catalyst 1832i AP, which is stuck in a boot loop and unable to boot from part1 or part2. I’ve tried TFTP recovery, NAND reconfiguration, and direct booting with no success. Here’s what I’ve tried and where I’...
Hello does anyone by chance posess a 8.5.x.x software version of wlc that you can give to me. I have a wlc 8.10.x.x version but it isn't compatible with my access point. Does anyone have it?
Hi,This is my second day at work and this is the first time i am working on a router, so my questions my sound infantile. I hope this community would forgive my ignorance. My company recently bought a C1121-4P Integrated Services Router.It has a USB ...
Hi,Question is regarding:* Cisco Catalyst 9800 -WLC* Cisco Catalyst 9120 -APIs it possible to put an AP into a maintenance mode? I want to stop new clients to connect to an AP and make already connected clients to gracefully roam to the neighboring A...
I have recently configured a C9800L. I created an SSID while setting up the Zero Day configuration. That SSID is currently broadcasting via the AP. However, when I tried creating a few more SSIDs, they were not broadcasting. SSID is enabled and broad...
Hi, We have two kinds of SSID networks in our environment. One is tunneled to our Central WLC (Catalyst 9800-40) and the other uses local breakout. For the WLAN that is tunneled, we want to use the same VLAN as for the SSID that uses local breakout...
Hi Guys, just a question, if my laptop wlan driver has been updated to support WiFi6E, does it mean that I can use the same wlan driver to connect to WiFi7 or do I need to update again my wlan driver to support WiFi7?
