Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello all,At our home/ office we have four AP121 clustered together as one. Every now and then our connected clients (iphone, ipad, macbook, windows tablets and laptops, …) loose the connection with the wireless and then we have to reconnect again. T...
Hi, i would like to know if i could use hte cisco 3850 as a pass through to register with cisco 5508 at our main site. at the moment i can see the AP registering to cisco 3850 and not 5508. if i plug in the ap to a csico 2960 will connect to 5508 ?al...
Hello Guys, I need some serious help, please!I'm having a heck of a issue getting my 3 AIR-SAP-1602I-A-KP (Standalone) device to work with my WLC 2504I was told by Cisco that the standalone version will also work with controllers, but i cant get them...
We have AIR-CT5508-K9 WLC's running with IOS Code 7.4.110.0.We are adding new authentication servers to around 550 WLC's.While adding new servers to WLAN's we disable the WLAN and enable after adding I would like know SNMP OID to check the status of ...
Hey....As the title suggests, I am having problems deleting floors and buildings from the map section of Cisco Prime. I screwed up while putting the map files in, and cannot remove them... it just times out. The only solution I have come close to fin...
hi all, When I tried to configure CMX on my MSE after adding the license i follow these steps: Choose Mobile Concierge Service > CMX Dashboard Configuration.Choose the Location MSE that the CMX Dashboard MSE gets the maps and location data from. It ...
We run into a problem when AP 3700 is connected to an 802.3at PSEthat only supports physical event classification as compliant to 802.3at standard for PSE,but does not support CDP/LLDP power negotiation.AP 3700 (I believe the firmware version does n...
Hi all,In short, APs will join the controller immediately using the recovery image, but once it downloads 7.6.100 and reboots, it either cannot join the controller or will take up to 40 minutes. The AP is in local mode. The AP 1040 eventually joined ...
I know that the WLCCA tool isn't officially supported, but I for one would love to see a webinar where we are walked through some of the tricks and tips to diagnosing RF issues with this tool. I know there are some WLCCA gurus out there, and would l...
I basically need a confirmation on a particular setup I'm seeing:Cisco 2504 controllerCisco 2602 AP'sAP's randomly will leave the controller and re join it. AP log will show all that plus all the radio interfaces resetting during this time.Also WLC ...
Hey guys, what is the Cisco replacement path to WCS? We just upgraded our wireless controller and it appears WCS has some comparability issues.
Hi Everyone, I have issue going on at our site.Users when they connect to WLC 2100 and get IP address and when they use the Remote VPN client they get connected to VPN but unable toaccess the internet sites and internal resources. Same users when t...
Hi Everyone, On Cisco WLC 2100 when user try to auth via Radius they get errorAAA Authentication Failure for UserName:guest User Type: WLAN USER I saw this error on WLC logs need to confirm if this error is due tosettings in WLC?settings in Radius?...
Hello All,We have set up a point to point link using two 1410 wireless bridges. The connection has been working for more than 1 year without a major issue.This morning, we have noticed that on one of the bridge the result of the show power-injector ...
WLC 5508 is installed at our main office and we want to install LAP at our remote location.confusion is that how Remote LAP is register with main office controller?
