I have both EWC9115AXI-K & C9800-L-C-K9 setup at the same place.The AP C9115AX attached to C9800-L is capwap image type, while EWC and any AP C9115 AX attached are EWC image type. I have a problem with the Printer Fuji Xerox Apeosport C3570 model.Thr...
Forum Posts
Hi experts, I know the way to change the IP state on "general-IP Config", but my query is that can we do that for all the APs on WLC together?I have hundreds of APs. Additionally, the DHCP server is in Linux server, not on the WLC. Thanks in advance...
Hi all, We have an issue with a customer on which we have deploy our captive portal solution. They have a Cisco WLC C9800-CL with AP in flexconnect mode. Users are seeing a 403 error message when they are being redirected to our splash page. One of o...
HI everyone My network environment is shown in the following picture，I looked into some loggs on my WLC 9800 and saw a bunch of loggs like this:%SWPORT-4-MAC_CONFLICT: Dynamic mac XXXX.XXXX.XXXX from Port-channel2 conflict with WlClient, please chec...
Hi, we have 1x pair foreign wireless controllers and 1x pair anchor wireless controllers. But can't login to anchor wlc standby unit, is it normal? how can access (ssh) anchor wlc standby unit? Can anyone please advise, thanks in advance!
I am in a new network that has AP switch port configured as Trunk ports with the native vlan tagged. I have always read to have them set as access port with the vlan set. Is there any benefit to either of these options. I do like looking in switches ...
Hello Team,We have two 9800 wlc running on 17.9.2 , both the wlc's are running in active standby mode.These wlc are installed in VM two different clusters.Please suggest best practise to reload asecondary node of the wlc.(our requirement the VM teams...
I am looking for some guidance on how to configure Cisco 1852AP with Mobility Express 8.10.185.0. I want to use MAC filtering with Radius server (MS Network Policy Server) for authentication and authorization. I have searched online but I could not f...
- FYI : https://www.wi-fi.org/news-events/newsroom/wi-fi-alliance-introduces-wi-fi-certified-7 M.
Dear Cisco Support Team, I hope this message finds you well. My name is Kashif, and I am currently working on configuring the Cisco AIR-CAP3602I-N-K9 device for our network infrastructure. I am reaching out to seek your expert guidance and assistance...
Resolved! l have AP-2802i-e-k9 l need configure
Hi l have alot of cisco AP-2802i-e-k9 l want configure then without controller and l want also setup wpa3 enterprise it is possible???
Resolved! WLC 4402 question
We have a WLC 4402 and I want to know if I can reboot all my AP's without going to touch each one at each site? I see an option under the Wireless tab, click on an AP then I see "Perform a hardware reset on this AP" will this just simply reboot the ...
Hello,I've setup radius for admins to logon to our 9800 (with ISE) but when I logon to the web admin portal I cant see any admin options. Just Monitoring and Dashboard.CLI seems fine.This is whats setup on the 9800:aaa new-model aaa group server rad...
Hello Team, Is it applicable to convert 1700 series or 1600 series AP to standalone and configure it to authenticate with Radius server?It would be appreciated if there is a document or a guide that describe how to configure it to authenticate with t...
Hello,I enabled RSSI low check for 5Ghz and 2.4Ghz, for 5Ghz set to -67 and for 2.4 set to -65but why on the client i can see there are still many client with rssi lower than -65 and 67?
