Hello,I have a failed scheduled task, i would like to see in the logging what went wrong. But which file can provide this information?With kind regards,Martijn.
Hello,I have a failed scheduled task, i would like to see in the logging what went wrong. But which file can provide this information?With kind regards,Martijn.
if you configure a wireless controller to not send any client traps, does that affect client information and stats in wcs? wcs is managing controllers, and the controllers are also configured to send traps to another third party trap receiver for ti...
We wanted to upgrade our current WCS(7.0.230.0) to the NCS 1.2 to support virtual Wireless LAN Controllers(WLC). What licensing/software would we need to do the upgrade? Hopefully there is a VM solution as we prefer not to buy a hardware version.Th...
I having an issue with WCS and the new code 7.4 on my WiSM2 blade. When I try to refresh configuration from/to controller it fails. I just upgraded from 7.01 and it worked before the upgrade. Is this not supported? I am able to change configura...
I'm sorry if this question has already been answered.I've got a WLC5508 (7.0.116.0) that is managed by WCS (7.0.172.0). I set up another WLC5508 with the same code and managed by the same WCS. Now I'd like to export all the 800 guest user accounts wi...
I am a heavy user of Flex connect. I have over 50 flex connect groups that I have created. Do I have to mirror these groups with the MAC addresses of the APs in the group on my redundant controller?Thanks, Phill
I have recently started at a new company. We have 12-14 SSIDs on each controller. I have noticed that wireless performance can be pretty poor at times. As I understand it, the controller will spend a set amount of time servicing each SSID. Therefore,...
All, Quick question. I'm currently logged into the web interface of my 1400 Series Bridge. I'm looking at the Radio0-802.11A Network Interfaces settings section and under Data Rates I notice the 54.0Mb/sec is configured as enabled but not required. W...
Guys,What is the maximum number of VLAN’s you can create on a cisco 1200 APthanks
Hi All,I've been working with ACL's for a while and needed to filter some iTunes share traffic on a specific VLANI assume VACL's will work for me. So, I created the following but it doesn't seem to be working.Can I get some assistance on this from an...
HiI thought that I might inform anyone planning to upgrade to version 7.3.101 on the wireless controller to have some deep thought before doing so. This is because, as I have discovered, audit between WCS and the WLC fails after upgrade to 7.3.101. T...
Guys,Which interface in Cisco AP1200 will be used if you want to use the 802.11a standard?Thanks
Guys,What trunking protocols are supported by the Cisco AP1200 series? Advanved thanking for your reply
Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
hello, recently we purchased cisco aironet AIR-AP1141N-E-K9 standalone model. after configuring it , client has no problem with connection and coverage, but there is problem with thoughput. clients are not able to connect at higher rates, eve...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-25-2024 07:13 PM | ||
07-17-2024 11:11 AM | ||
07-17-2024 06:04 AM | ||
07-08-2024 04:04 PM | ||
06-26-2024 02:25 PM |
User | Count |
---|---|
7 | |
5 | |
2 | |
2 | |
2 |