Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Wireless Access point license
Hi, we have 5520 wireless controller and some 3820 APs are online. Now we purchase some 9100 access points and need to add them to this WLC. Do we need to add new AP license to WLC? If yes, what is the procedure? Can anyone please advise, thanks in a...
Resolved! Putty hangs when connected to 3502i
Let me start by saying this is for my homelab and I bought the 3502i off of ebay, i'm trying to factory reset it for use in my personal networking setup for study.As a premise, I've never had issues with my Cisco 3750-x, 3850, or Juniper srx320 secu...
Hi All,Last night I was performing mainteance on access points throughout the network. I was converting them from Local to H-REAP to allow for vlan support. The maintenance went well however afterwards I've noticed access points are not showing up in...
Greetings to everyone How to stop QR code user passowrd sharing for wlan wifi users on GUI of Embedded wireless controller?
Guys, as you can see in the attached picture I noticed that some ssids operate in 802.11ac while the other ssids are only broadcast in 802.11n even though they are using the same access point.So where can I change that?
Resolved! 9800-CL Network Configuration
Hi All, I'm setting up a Cisco 9800-CL WLC and I want to check if there are any issues with using a single VLAN/IP for both WLC and AP management? We currently have a management VLAN that is presented to our ESXi hosts and we dont want to setup a se...
Hey Guys, i noticed that one of my APs (2702i with 8.10.185) in a remote branch office decided not to serve any 5GHz clients. Upon some investigation i found out that its 802.11a radio is admin UP but oper DOWN. AP is powered via PoE and has full pow...
Hello Professionals,I'm configuring 3 SSIDs and those has same security conditions. (WPA/WPA2 - Macfiltering)I would like to grant different connect rights for each devices. For example) - SSID: AAA - SSID: 123 - SSID: 000and there are 2 client de...
I have installed the embedded controller image on C9115AXI-D access point and working fine till it is rebooted. once rebooted it boots in to IOSXE image but no connectivity (no ping no http or https). gig0 interface is up but self ping also fails.I h...
Hiwe are getting this error from a cisco C9120AXI-E (V07) AP, when talking to our WLC.[*03/08/2023 16:04:57.4903] CAPWAP State: Discovery[*03/08/2023 16:04:57.4903] IP DNS query for CISCO-CAPWAP-CONTROLLER[*03/08/2023 16:04:57.4923] DNS resolved CISC...
I'm having an issue where the wireless guests are disconnecting after 15 minutes and are prompted to log back into the captive portal.These are the configurations on the Mobility Express Controller. Can someone please advise if theire is a setting th...
Hello Professionals, I have a question about DHCP snooping with trusted port. I have Cisco 9300 switch and wlc9800 controller is connected to this switch.Wireless client can get IP address from the DHCP pool from C9300 switch.When I tried connect SSI...
Hi All, I am looking to restrict per client user bandwidth for our Guest network on Cisco 9800 WLC's. AP's are in Flexconnect mode.IOS version is 17.3.5aIs this possible on catalyst WLC like Aireos based WLC's? -Kamal
Dear Experts, Hope all are well, I need some some info if some one can share it woul be great!I am looking for Posture, CWA and WLC integration configuratoin if someone can share the configuration steps it would be great.Warm regards.
Hello Professionals,From 2 days ago, my wireless controller (WLC9800-L) freezing suddenly.- version: 17.9.3This device is directly connected to C9300L switch port with Trunk - Trunk(with allowed port).I was accessing Web GUI of controller, but sudden...
