Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi,we have a scenario with two remote sites. Site A is the central office and Site B is a remote location.In Site A we have a 6509 with WiSM and we have configured all the AP on these Wism (Site A + Site B APs).We need to use the same SSID in Site A ...
Hi AllIn Cisco NCS shell I have incorrectly entered the following command in order to chang ethe admin password and saved itusername admin password hash <password> role adminand hence lost the access to shell (ssh). Is there a way to retrieve or rese...
I have the situation where I need to talk to multiple different Radius servers depending on the WLAN. Some of the WLANs are not able to route traffic over my entire network, and within these secure areas the Radius server for that area sit. Is ther...
Hi Experts ,I have WCS 7.0.172.0 where as i have very frequent alert about DoS : CTS flood In channel 60, the system has detected 212 CTS frames in the last minute, which matches the traffic pattern of the form of denial-of-service attack, CTS (Clea...
Hi Friends,I have Cisco 1140 access points and 5508 controller in my network. I have configured 2 SSIDs. One SSID is working fine, we have issue with second SSID. Clients getting connected to second SSID are facing the latency issue, latency is aroun...
Hi all, appreciated if you guys can answer this.I have Cisco 2100 need to set up in DMZ and Air-Lap1131G as AP.Right now i connected the WLC console to a PC to run the initial bootup in terminal and i really need the info that it required.Now i have ...
Hi,My client has a wireless setup consisting of a WLC 2112 and about 7 1131AG LWAPPs. There are two SSIDs, say CORP(mapped to VLAN 900) and GUEST(mapped to VLAN 901). Wireless clients get IP through DHCP. DHCP IP is configured in the Dynamic interfac...
Hello,We have 2 Cisco Aironet Power Injector LR2's (AIR-PWRINJ-BLR2=) and I can't console to either using Cisco sky blue consoel cable.I am using putty and my setting are:Speed = 9600Data Bits = 8Stop Bits = 1parity = noneFlow control = none
hi....Do Cisco have an appliance that can authenticate user & display web access report ?---Posted by WebUser Aku Apit
whats the maximum opreational distance of a Cisco Outdoor wireless access point?`
Hi,Please find the below attachment and give me the best solution to cover indoor and outdoor wireless signal. The area has covered Villas with concrete walls and the area dimension is 200/100mtrs. Please can anyone tell me is there any single ante...
Hi ALL,In our setup we have WiSM modules installed on cisco 6506-E, ACS 5.3 virtual appliance.We are trying to implement EAP-FAST for our Wireless using WPA/WPA2 802.1x on the WLC side.I have followed the instructions in the following document step-b...
Say you haveNetwork192.168.10.0/24With IP address Range:192.168.10.1 through 192.168.10.254Broadcast: 192.168.10.255And you want to block the address range 192.168.10.10 through 192.168.10.20 from the network 192.168.10.0/24How would you find out the...
I am looking at getting the UC320 or the UC540. Using it with a small company about 10 users. Will either of those system support the iPhone Mobile 8? Only 2 users would need the iPhone support, does the cost out way the benifits?
Is it possible that users can roam between Cisco WLC and other vendor wireless gear? Meraki keeps saying it is possible.They keep saying it is a IEEE feature and everone should support but I do not understand how?
