Wireless

I have a 1240AP in my companie's office.   We want to have two SSIDs setup on it, one for internal use (connected to the corporate VLAN) and one setup as a guest network for company visitors.  We can connect to either SSID and they both seem to be wo...

Hi,In an LWAPP environment, who does the 802.3 to 802.11 frame translation ? I thought it was the WLC alone that did it.However, in the Cisco Press book, "Deploying and Troubleshooting Cisco Wireless Lan Controllers", it seems to suggest,that when fr...

I'm looking to setup some new 7925Gs with WPA2/Enterprise with WLC 4.1 and Cisco Secure ACS 5x.  Any documents on CCO I could reference? Feedback? Where on the 7925 do I setup WPA2/Enterprise? or even just WPA2 ?

Does Cisco make a high gain antenna for the 881w?If so, I would greatly appreciate a product number.Thanks!James E

I'm upgrading the radio unit in a 1100 series access point using part number AIR-MP21G-J-K9-AWhen turing the unit on the radio module is failing because it can not find the firmware 5501.img. When looking in the .tar file of all the 123-8 IOS's avail...

I know this will sound rather simple to most, but I can not tell if these are going to be compatible with my 2125 controllers. I believe they are light weight access points but do not see that mentioned in the docs I can find.are they compatible with...

Hello,we have a deployment of two WLC4402 (Version 6.0.196) with Mesh APs 1522 and AP1242 (Outdoor and Indoor).Two Questions:1) We control the Access-Point with a network management systems (Ping in regular intervals). Some times, APs are not reachab...

Hi,I have upgraded the WLC - 4402 from 4.2.130.0 to 4.2.176.0 after the upgrade all the AP's associated with the WLC has been disassociated and it never associate again with the WLC.  I have revert back the change to older version 4.2.130.0 but no ch...

Hello *,i have two questions regarding GGSN Release 10:1- Regarding eG-CDRs, from the documentation i undestand that for release 9.2 and later, Charging Release 7 MUST be configured, otherwise no Service information will be included on the CDRs (that...

Hi,I am trying to deploy a NAC appliance incorporating dot1x. It works a dream on a Cisco AP1232G when it only has one SSID configured, however, we need to include another two SSID's which are WPA.The command mbssid on dot11Radio0 interface is what i...

/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5...

Hi Experts!I have two AIR-LAP1510AG-N-K9 units that I want to convert to Autonomous Access Points..actually I want to run them as a Wireless Bridge truth be known. I have done some backround reading on Cisco.Com and around the WWW. I am confused as t...

Hi,  My customer wants to create guest users in wireless lan controller. We were successfully able to create that and it worked . But the problem is that to access the internet the users have to change the "proxy server" settings on the internet expl...

Folks,I have a doubt. I do have at present 4400-50 , which have 50 N-Access Points installed and it is full. This is deployed already. Now I need to add around 80 N-AP's . Can I propose 5508 series controller? Will it be compatible with existing 4400...

Does somebody knows how to take the Aironet 1020 out of site survey mode?Thanks