Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
HI All ,I am new to wireless . I am using WS-SVC-WISM-1-K9 wism module and using 5 Access points . When my clients are moving from one access point to another we are getting packet drops . Kindly anyone suggest me what all configuration i need to ...
Hello, I have 3 WAP4410N,I want that clients to connect to the nearest access point, but it does not, the roaming not is working fine, and always connect to the same access point even if the signal is very low, how I can fix it?, Do you think tha...
Hi all,I have two AP 1240s at a site, both with the same firmware and configuration, and all users are configured correctly to connect to the network. AP 2 is having some type of issue that is not allowing a complete connection to some of the users. ...
I got following on fewer APs while other APs are working fine with same OS and WLC kindly guidecapwap ap ip address 152.109.100.11 255.255.255.224You should configure Domain and Name Server from controller CLI/GUI.amt_pkwalls1240AP011#capwap ap ip ...
I am using a Cisco 881G router with cellular card PCEX-3G-CDMA-V.The correct version of software is running according to the Cisco product overview documents: flash:c880data-universalk9-mz.124-22.T2.binWhile I am using the cellular connection surfing...
I have a wireless problem on the 800 series and with two PCs connected to the wireless router and you're a 40GB file to send by second PC over the wireless module does away is this normal?
I heard that it would be possible to configure WiFi-network in such a way it allows only devices of which the AP’s get a RX-signal that is above –xx dBm.This would prevent access from devices ‘far away’ eg: devices at BT office or Golden Tulip hotel,...
Hello to all, i have a Problem with a wifi client.The client login successfully and the 26 seconds later the client recieve an idle timeout from WLC.*Dot1x_NW_MsgTask_0: Jul 15 12:53:22.471: 00:24:7e:a8:2a:2b x.x.x.x Adding Fast Path rule type = Air...
Interested in facilitiating the ability for the receptionist (or anyone for that matter) to be able to create a day pass for guest wireless access. The idea being that the guest would receive a pass that allows them access to a site's <20 access poi...
Hello;We use approximately 100 ap (1242ag) with WLC4400 series controller. Unfortunately some of our ap reduce other ssid which places closed to our ap.What we supposed to do to keep from this situation ?ThanksBest regards.
I want to use my dual radio 3502e AP to service clients on the 2.4 MHz and do a point to point bridge on the 5 GHz. Is that possible?
Hi, I have a customer that needs to extends its wireless network wirelessly. All the AP:s (AIR-LAP1242AG-E-K9) are managed by a WLAN Controller (AIR-WLC2106-K9). One of the AP needs to be extended, which i'm guessing, with WDS. This AP needs to have ...
HiI have a couple of 114n APs in my network and the CAPWAP uptime and AP uptime are almost the same. But there is one which always resets after some time. I have moved across to another switch port but the issue persists. I have other 1141 and 1131's...
Hi, Some body can help-me about how can I store the file config.txt on Cisco aironet AP1231g when the size of this file is more than 32kb (ex: 45kb long)?, the size of the NVRAM is 32KB. After I have had a error message of buffer size, i...
Dears ,I have upgraded my WLC from version 5.1.151 to version 6.0.202 and then to 7.0.116 .Since when , I see that all clients are disconnected every around 20 minutes and re-connected again .Does anyone has any clues ?WLC is 4402AP are AIR-LAP1231G-...
