Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
We have a Cisco Catalyst 6500 Wireless Services Module. We need to authenticate user with an external ldap server (or radius server). How to authenticate user with login more than 24 caracters. Wism send 24 caracters max to the server.Thanks for your...
Hi, [From H-REAP deployment guide]===============================Roundtrip latency must not exceed 300 milliseconds (ms) between the access point and the controller,and LWAPP or CAPWAP control packets must be prioritized over all other traffic.[From ...
Hello there I am 1242 LAP, with 2 controllers. Everything is operating fine. but the signal of the AP is weack eventhough i am very close to the access point. I have 24 antennas for 8 access point. All of them operate on 2.4GHz, I tried all possible ...
hi all, I am facing a problem with WLC 4402,We have a lab having 20 laptops.The scenario is that clients are Randomly get stuck after using for some time.We are using windows ( XP )wireless client utility.Clients get connected to the AP smoot...
When I go into WCS it shows me a chart oh how many people have connected on certain dates.One bar on the graph is blue which means assoicated clients. It tells me I have 40.The other bar is gold or yellow. It tells me I have 38.We might have 2 people...
Resolved! Minimum Connect rate 1140AG
I would like to limit all connections to a minimum of 9Mbs. I tried using the speed basic-9.0 command on the dotradio 0 interface. This seemed to limit me to only 9 and nothing better. Is there a better way to configure this?Thanks
Hi Netpro,I've got an existing H-REAP deployment, and I've noticed that changes to the WLAN configuration on the WLC does not update the remote APs immediately. Is there a timer, or some logic that is used in updating APs that are configured as H-RE...
Currently have a corporate SSID advertised enabling clients to connect using either A or G. Ideally I'd like clients too connect using A if they're able, and if not connect on G.I think I've read on these forums this is possible but requires the WLCs...
Hi, I am just looking at a Cisco 1131g AP and notice there is no control-plane command. Does anyone know why? AP is running 12.4(10b)JDA3
Resolved! Bandwith LWAPP
Hi,Does anyone know the reguired bandwith of the LWAPP control traffic for one Access-Point?regardsPascal
Hi,I need to provide several WLANs that need to have different SSIDs, but can all go on the same VLAN.An example would be if i have 40 schools and one large, flat guest LAN that I want to use for them all. I'd like to put (SSIDs of)school0001, schoo...
Resolved! OoS SNMP Value on WLC 4100
Hi Forum:I need to monitor through snmp the Out of Service radios of APs. The Wireless Control System give me through web based application that number, but I need on snmp. I really appreciate if somebody can confirm if this value is accesible throug...
GentsI 2 WISMs and 2 4402 controllers. the WiSM are the foreign controllers and the 4402 are my anchor controllers. I am trying to add them to the WCS for management purposes. however, I am not able. knowing that I have ICMP reachability between all ...
I've been playing with this new Cisco Aironet 1252 Access Point and it's pretty cool.My question to you guys is, when I set up an ssid and enable my dot11 radio 0 interface, I go to view my wireless networks in Windows XP and the SSID I have configur...
Hi, what is the best practices in this case. Use wired data and wireless data in the same vlan? or use differents vlans for wired and wireless data connections?I have this doubt but a think that the correct is use on vlan for each, wired and wireless...
