Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Resolved! Rogue detection

Hi, I would need some clarifications about rogue AP detection. First, in order to configure the passive rogue detection is it necessary to just setup a rogue detector AP or I also need to enable RLDP? Second, in your experience how much is it reliabl...

I need DOS drivers for an AIR-PCM350. I obtained documentation from Cisco's website indicating that I need to download dosdrvs.exe from the Wireless software center. Unfortunately, I have not been able to locate it. Does anyone know where I can obtai...

jwhite by • Community Member
  • 2120 Views
  • 2 replies
  • 0 Helpful votes

Hi,We are running WCS Version                                           6.0.181.0 and had a 5508 WLC fail that was connected to this WCS. The WLC was replaced and is running the same config and Software Version                 6.0.196.0.In WCS the ol...

Tony Dann by • Community Member
  • 1875 Views
  • 2 replies
  • 0 Helpful votes

WLC WAN BackupMy customer would like to have a Backup-WLC-Controller at their main site. On the remote site he has a 5508 with actually 6 accesspoints.On the mainsite he has also a 5508 which acts as backup only. They have a 2Mbit WAN between this tw...

Hi all,I am a newbie about Cisco wireless.I would like to ask some questions. How can I change the Registered Controller on the AP when my network has 1400APs and we have 8 different mobility groups and each group has 4 WLC controllers.I set primary ...

netwrk197 by • Community Member
  • 1138 Views
  • 1 replies
  • 0 Helpful votes

Hello, I have a question regarding our wireless guest network and using iPADsOur wireless network consist of (3) 5508 WLC’s running 6.0.188. 2 internal WLC and 1 external anchor WLC for guest.  Presently we are only using one of the internal controll...

JOHN SAINATO by • Community Member
  • 1194 Views
  • 1 replies
  • 0 Helpful votes

Hi All, Does anybody know if there's any limitations or bugs to use WLC's service interface IP when add WLC into WCS?Another question is I remember there's a post previously says that there are a bug regarding to ARP if the WLC not using LAG but conn...

bbxie by • Level 7
  • 7131 Views
  • 10 replies
  • 0 Helpful votes

   Hi,   Today I have a WIPS Server which send SNMP Traps to a WCS and I can see the alarms generated by the WIPS in WCS...   Is there any way for me to send the events or alarms created by WIPS to a Syslog Server ???   Regards,   Andre Lomonaco

lomonaco by • Level 4
  • 1114 Views
  • 2 replies
  • 0 Helpful votes

Resolved! wlc-2106

I saw in a recently published book that the wlc-2106 is based in a asa5505 hardware.for testing purpouses how chan i switch between those operating systems (asa <->air..)?.Thanks.

We are using Cisco's Cellular PCEX-3G-CDMA-V async interface for Internet access. Works wonderfully and very fast.  Everything seems to be operating correctly except for defining interesting traffic to control the link.Inintally the link is dialed ba...

fsebera by • Level 9
  • 1038 Views
  • 0 replies
  • 0 Helpful votes

We currently have two 4400's along with WCS. We would like to add an additional 4400 to the group. I have read the documentation and not come across a clear cut example of adding an additional 4400 to a production  group.Thanks

gginty by • Level 2
  • 890 Views
  • 1 replies
  • 0 Helpful votes

I have two 5508 WLC v7.0. Two locations.  Assigning Primary and secondary controllers to the APs how long would a client be "down" if a controller failed (assuming all APs are on one WLC) Would the type of wireless security be a consideration for spe...

ptilling by • Level 2
  • 1573 Views
  • 4 replies
  • 0 Helpful votes