Wireless

Hi,We have a problem with the mesh connection of 1242AG APs converted to LAPs. We are using WLC-4402-50 with image version 4.1.192.35M MESH which is the latest for indoor mesh. Whenever we start to establish a mesh connection, the LAN just suddenly h...

Hello,we updated out WISM and WLC to 5.2.157 and now we could not see the "WLAN Override" settings and all SSIDs are on all access points available. We know that 5.2 is very new and it is dangerous to use such new versions but we need some feature of...

I would like to consider upgrading the firmware on my 4400 WLC from version 4 to version 5, but wondering what the steps would involve on doing this. Is it a major project to do, or is it fairly simple? I've been having issues with my AP's finding th...

Hi,We do the initial setup for the controllers but there is no connectivity between the SUP720 and the WISM through the management interfaces. The management vlan is 40 and the IP address assigned to the controller is 10.127.140.10/24 and for the sup...

I get a permission denied when I try to run the Trace Switch Port on the WCS. The WCS tells me the rouge is on the network. But I keep getting this message. Windows 2003 server, WCS Version 5.2.110.0. 2 Wism's running version 5.2.157.0. SNMP 2v with ...

Hi every body! I am looking for a link about EAPOW or EAP over wireless describing the feilds in side EAPOW frame.Thanks a lot!

I just purchased a WLC2125 to centrally manage my 1242 AP's. At our corporate office where the controller is located i want to run DHCP for the clients. At the remote sites I have REAP enabled so that the local devices can access local resources. But...

<p>We have a small Vocera deployment and just upgraded to Vocera version 4.1 and are seeing one way audio or dropped calls.  We are not running an LWAPP solution yet and our Access Points are version 12.3(4)JA.  We have verfiied that the badges are n...

We hve this problem.We have a network, working properly since 2 years, of 15 autonomous AP (mix of 1200, 1300 and 1400).One of them is WCS master, we have configured few ssidd.Now we are migrating to LAP and WLC 4402, all seems to work properly in la...

I set up both ends of this bridge (about 1 mile apart) and I get an association, so I think I'm golden... well, I haven't been able to get the web gui ping/link test to work at all across them, so I upgraded to the 12.4 IOS on the main site, then wen...

Folks -I am about to upgrade my system from 4.1 code to 4.2 code. I am wondering if it's possible to have the WCS and 2700 Location Appliance upgraded to 4.2 d-cubed revs first while still running Concannon WLC code 4.1.185? I am hoping to be able...

Hi,Working with WLC and WCS (v5.2), does the Client Walkabout is still valid? can i use it for enhance my heat maps?How can i refine the heat maps in WCS?Thanks in advance.Cheers,

We have one 1310 (root) at the office feeding two 1310 (non-roots) down the road (1/4 mi). One of the units is much slower than the other and we can't figure out why. Both have the same signal strength and snr. Signal Strength (dBm) -52 Signal to Noi...

I am begging to migrate all of my wireless links to WPA, currently they are unencrypted. I have a few computers that recieve there connectivity via wireless link. I need to have these computers establish an ecyrpted wireless link so domain users ca...

Hi, we are about to deploy a wireless system for one of our customers and we have a few questions. The AIR-ANT1949 will be used to transfer the signal about 300-400meters to a building with one laptop. Line of sight is "quite good". The AIR-ANT4941 w...