Wireless

Hi,We have a 1200 Aironet AP which had been working fine. The image directory was deleted from the AP with the "delete /recursive ...." command.We TFTP a new image file namely:c1200-k9w7-tar.123-8.JEB.tarHowever when we reboot the Access Point it com...

My customer who has one WLC4402,36 AP1130.Some of APs miss from WLC sometimes but I can ping those APs at this time.I can not find any messages from WLC(version 4.2.61).Any suggestions?

Are there any recommendations for load thresholds for n access points? I know that with n the APs should be able to handle more connections than their g counterparts.I have done tests where 29 clients have been attached to one 1252 with little or no...

I have an 1131AG (autonomous) that was previously configured with the mode button disabled. As a result, I cannot hold it down on power up to restore a default configuration. I do not know the login for the AP to undo the configuration of the mode ...

What is cisco best practice for a LWAPP port on an edge switch. WLAN is using 7921 handsets.Should I use STP portfast ?What QOS marking on the access port.### current ####int fa0/1switchportswitchport mode accessswitchport access vlan 10mls qos trust...

Currently one of my customers is running Autonomous IOS version 12.3(7)JA.He wants WEP and WPA support and in future wants to able to be convert from Autonomous to LWAPP.According to the following link version 12.3(7)JA should allow him to go to LWAP...

Hi,We are setting up Tacaacs to a WLC 4404 , but we are getting the following message on the WLC when we try and go through the management IP using tacaacs. Anyone seen this b4.Jan 29 13:23:28.012 ews_auth.c:2107 EMWEB-1-LOGIN_FAILED: Login failed. ...

I am planning to split AP's between 2 WLC's. Also need to configure DHCP option 43, since the Management and AP-Manager interfaces will be on a different VLAN than APs.Is Option 43 going to overwrite the primary/secondary controller configuration on ...

We have a autonomous wireless setup with a WLSM and WLSE. I have an issue with where I have 2 wirless clients that need to communicate using a multicast address for an application to work.The clients can ping each other but the multicast stream is no...

Why does the WLC map the DSCP to the LWAPP's 802.1p field when the LWAP does NOT understand this field in the LWAPP data unit? In fact, the LWAP does NOT mark this field for frames going towards the WLC.Also, why does the wired switch bother with 802...

Hi all,I want to start streaming multicast video across wireless. Lucky for me, the stream isn't of too high bandwidth (100-200 kbps). However, it is multicast based so: UDP packet streaming, no ACK mechanisme.Our setup is completely WISM based.Howev...

Good afternoon,Can anyone tell if i can connect a Access Point (AIR-LAP521G-E-K9) and a Controller (AIR-WLC526-K9) to every kind of Cisco Switch (Catalyst 29XX, Catalyst 35XX, etc...) or only to Cisco Catalyst Express 500 Series.Thank you very much f...

Can ayone confirm what is the industry standard Tx power level for a test AP and when simulating AP for a WLAN survey? I think I read somwhere its 25mW and not 50mW?Thanks

Is there anyway to have or configure a Hot-Standby Root Bridge for Autonomous AP1242?My purpose of hahving this is to have a more resilience in case the Active Root Bridge is faulty on the backhaul side.In order to have more resilience backhaul for t...

Hi all,I have two AP1240 on remote office, which is connected to company headquarter by WAN. AP's were converted from standalone to lightweight mode without problem, but they now cannot join WLC, which is in company headquarter. Degug lwapp on WLC sh...