Hello,for planning where to place a Cisco Access Point 1130AG, I need to know in which area around the signal is provided and in which strength.Thanks.Andreas
Hello,for planning where to place a Cisco Access Point 1130AG, I need to know in which area around the signal is provided and in which strength.Thanks.Andreas
On my WISM, running 6.0.182, I configured the message on the web login page with our normal disclaimer. However when the Guest Login Page is displayed for the users, the message does not wrap and runs on and on to the right. The spacing on the word...
Hi alldo 1242 ap's try to associate with WLC4404 using lwapp then capwap, how many times do they try lwapp? I have had them all connected to my controller, I have reboooted my controller and they are all taking a long time to come back on, why is thi...
Anyone know what WLC version is supported on a WiSM running in a 6509?Currently we are running 4.2.61.0 and i have noticed on the Cisco website that its up to verison 6.x.x.How can i find out what version our 6509 will support?
We recently purchased a dozen 1142's which I added to our 4404 controller running version 6.0.196.0.I can't connect with the 802.11n protocol to any WLAN configured with WPA2 Enterprise, WEP, or WPA Enterprise with a pre-shared key.I successfully con...
Hi all, I have ACS 4.2, I can't get it to authenticate my wireless clients. I am still getting EAP-TLS/EAP fail during HANDSHAKE. I triple checked my cert at both end and everything under advance setting tab is all good. I can use the same s...
Hi all,does anybody know where I can find information about limitations and recommendations of the following values?I already checked cco but did not find anything in the data sheets, configuration and design guides.1. maximal vs. recommended SSIDs o...
I currently have a Cisco 801 configured as a root access point. I would like to configure my 541 as a wireless repeater, but I can't seem to find any documentation on how to do it. Can anyone point me in the right direction?
We have a Cisco Aironet 1200 series, I enabled WEP Key and it worx fine. However I wat only 8 devices (MAC Addresses) to be able to connect to this device. ie WEP key is readable via Windows 7 etc thus users are fiddling on the WLAN. I want to lock ...
I just went in to trace a rouge in the system and WCS tells me that I already have 10 allowed traces running and I will have to wait. How can I see what is being traced and how to kill those traces that I need to.I'm stuck with a rouge that I'm havi...
Our wireless network consists of Wireless LAN Controllers and multiple APs. We require 802.1x authentication on our SSID. We use IAS as our authentication server for both machines and users. Each device connecting to our WLAN is required to have a...
Hi allCan anyone please help, my 1242 access points will not join my controller, I have done a debug and can see the Access point sending a discovery request, then the controller says discovery request sent, but then nothing happens, any ideas what t...
I have the install guide but can't seem to find the manual so I can set http and other stuff.thanksGary
The certificate that is installed on the wireless clients and the ACS will be expiring. The cert on both was installed from a Microsoft certificate server, which needs to be replaced/upgraded. What do you think of this plan to renew the certs?1) Cr...
I have a guest access network supported by WLC and managed by WCS and use the default web login paged.I would like to upload a customized page using the web auth bundle option. I do not want to use an external server. I can generate an acceptable HTM...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |