Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

HelloI have 30 access points with 2 WLC 4402 each one connected to 6506 by just 1 link,as 4402 support 25 access points ,what can i do in this situation?1)do i assign 15 access point to each WLC?e.g 15 LWAP per controller?or what?2) is it recomnded t...

alsayed by • Level 7
  • 1008 Views
  • 3 replies
  • 0 Helpful votes

Hi all,If I have wireless ip phone 7921 connected to access point.Access point is controlled by wireless access controller.How RTP traffic moves?wireless ip phone----->access point----->access controller----->access point------>wireless ip phoneorwir...

Hello,I try to configure a WLC4402 new out of the box. If I make a console connection for initial configuration I see the boot sequence in my terminal software but I am not able to send keyboard commands. the session does not accept keyboard input. I...

ERIK BOSMANS by • Community Member
  • 8464 Views
  • 2 replies
  • 0 Helpful votes

We have a setup of two WiSMs (4 WLCs) in the HO and multiple branches connected to theHO through MPLS with the same ISP.In one of the branches, the APs are unable to join any of the cotrollers. Itroubleshooted this issue from different aspects with n...

shasanain by • Level 2
  • 2835 Views
  • 8 replies
  • 0 Helpful votes

hi,i have one Cisco 4402 Contoler which is running in image 4.0 Version, and i tried to upgrade this image to 5.0 , but it stops tranfering data once it reached 33 MB of size, am using TFTP-D32 as tftp server, ( i checked Cisco TFTP Server too ), but...

cmanvar700 by • Community Member
  • 1242 Views
  • 2 replies
  • 0 Helpful votes

I'm running WCS 6.0.181.0 Linux. 2600 APs and about 10 WiSM blades. I need to move the application to a bigger server (the server is running slow). I'm planning on keeping the server name/ip address to avoid licensing issues. Can anyone guide me thro...

jjiles by • Level 3
  • 947 Views
  • 1 replies
  • 0 Helpful votes

Hello Everyone,     I have a AP 1250 and I would like to channel bond with the 5-GHz 802.11n radio; to get more throughput. I have found some articals how to do this, but it's for the non autonomous AP GUI setup. Does anyone have the IOS commands to ...

58182 by • Level 2
  • 1907 Views
  • 2 replies
  • 0 Helpful votes

In WCs version 6.0.181.0 the RF Calibration Models command is missing from the drop down menu on the Maps page. Does this required a more than a Base license (it was there with the Demo license)? I can't find anything in the documentation saying this...

pinglis by • Level 5
  • 1390 Views
  • 2 replies
  • 0 Helpful votes

heyExpert as we all know while conducting WIPT survey we have to consider  following characteristcis which should not be exceed from specific valueRSSI=35 SNR =25  Signal Strength = -67  these are values for 80.11 b/g surveywhat if  i condcutng a sur...

I have a client that connects to an Access Point on the floor above.  The connection is "Very Low" and pings are choppy.  Is there a way to force the client to connect to the Access Point on its own floor down the hall.Using 1131AG  Access Points; WL...

msekula by • Community Member
  • 12704 Views
  • 2 replies
  • 5 Helpful votes

This is a generic question... how do u validate wIPS alerts if your wireless devices are spread in different physical locations(buildings, cities, states, countries)?For ex: /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal";...

Review Cisco Networking for a $25 gift card