Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

I have a WLC (4402) running version 5.2.193.0.  The WLC used to have both interfaces connected to a single switch (LAG was enabled) with etherchannel on the switch end.  It was changed such that each port on the WLC is connected to a different switch...

Hi folks,I've run into an annoying issue with 6.0.196 with my favorite (Motorola/Symbol Fusion) client.  Ever since some testbed controllers were upgraded, Symbol MC90 handhelds have been unable to roam successfully across controllers.  The EAP-TLS c...

wififofum by Level 7
  • 3283 Views
  • 4 replies
  • 0 Helpful votes

Hi allI am new to Cisco and I need to upgrade the Cisco AiroNet 1200 AP's at my place.The current version is 12,2(15) JA I am not sure what is the latest version available, the reason for the upgrade is to allow WEP Encryption which is not an option ...

Maelito77 by Community Member
  • 2499 Views
  • 1 replies
  • 0 Helpful votes

Hi there,Few times I heard you can change the polarization of the Cisco Yagi antennas from vertical to horizontal by turning the cubical part of the antenna by 90 degrees. What do I gain from doing that and how would it improve my signal lever and SN...

I have an BSSID enabled AP and all Vlan clients should be authenticated on one IAS Server. On the Server the Vlans should be mapped to different Remote-Access Policies. I was not able to find any command for the "aaa group server" configuration, that...

philipp.wolf by Frequent Visitor
  • 2575 Views
  • 3 replies
  • 0 Helpful votes

i´m tryng to implement a wireless network using a AIR-WLC2125-K9 controller, and AIR-LAP1252AG-A-K9 access points, NOT using any ACS.Somewhere i read that the WLC can authenticate a local database off users that are locally defined or in a LDAP (Acti...

jose.macias by Community Member
  • 1017 Views
  • 1 replies
  • 0 Helpful votes

Hi,Currently in the process of deploying some Cisco 7921 handsets. Most things appear to be working well with them, accept we're having some issues with roaming when the phones are switching between Access Points, we experience voice gaps of up to 5 ...

Resolved! WCS services

Good day!I need some help about WCS 6.0, I installed it on a virtual machine with Windows Server 2003 in which previously have installed CiscoWorks. I have this PC just for testing purposes so it's not a dedicated server. My question is what services...

karlareyes by Level 1
  • 3795 Views
  • 12 replies
  • 0 Helpful votes

I saw in documentation that i can upgrade directly from ACS SE 4.1.1.23 to 4.2, but i received software upgrade kit that says upgrade from 4.1.1.24 to 4.2.My question is must i upgrade first to 4.1.1.24?Thanks,Best RegardsMC

etmarcof by Level 7
  • 798 Views
  • 1 replies
  • 0 Helpful votes

We are trying to configure email notification on a WCS running version 6.0.170.0 .The mail server we used is MS exchange. We have already defined the email ID's, email notification Alarms and the mail server  in WCS. The manual test of the configurat...

I'm getting ready to make some changes to the existing controllers by changing out the IP's Address for Managment,AP Manger, and service port for a client.The question is in what order do I make the changes?????Do I start with the service port (save ...

jcomment by Community Member
  • 8119 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Cable distance

Hi, i hope someone will be able to help me out. I'm trying to deploy an AP with a max range from the switch >100m. The question is can i pull a 100m cable from the switch to the power injector and another 100m from the power injector to the AP?switch...

tookenyip12 by Community Member
  • 988 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card