Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Morning all. It seems that I may have entered the improper crypto key value when setting up SSH. Can someone tell me how to get rid of the current key, so I can regenerate the proper key length. Normaly I use 768, but may have missed a key.ThanksP...
Hi all, I want to know how can I check the status of antennas of AP 1252 in lower power mode.My customer has not yet the POE Plus switches so the AP can not make the most of use of all antennas. AP 1252 has 3 Rx and 2Tx antennas but it does not use a...
Hi,I'm looking for any updated on the integration of Cisco WCS and/or Navigator with Cisco Works. I know that earliers versions of WCS had no integration with CW, other than being able to launch WCS from within CW. Have been reading documentation on ...
I have two WLC 4402 connecting to core sw1 and core sw2 separate.Scenario:native vlan 4(management) & vlan28(ip cctv camera)WLC<---trunk allow vlan 4--->core switch<---trunk allow vlan 4,28--->edge switch <--trunk allow vlan 4,28-->RAP<<<backhaul so,...
Has anybody seen code version 5.2 or higher have a problem with HREAP mode APs losing their local vlan mapping and reverting to centrally switched interface vlan tag??
Hi,I have a problem with port 2 in Wireless Lan Controler 4402. The problem is that the distribution port 2 of the WLC not link with the switch (3750). We receive the WLC and we follow the autostart wizard and we enable LAG. The wizard finish, I rest...
I'm seeing this on the integrated WLC within the WS-C3750G-24WS-S50, when attempting to use the LAG ports the switch only shows one of the ports as up. I have tried several things to troubleshoot on both the switch and the WLC but so far the other po...
HelloMaybe someone can help me?I am looking for a German template for the User Interface on my Cisco NAC Guest Server.Someone knows where I can download it?Thanks lot for the support.Greetings Esteban
Dear All,could you please help me how to configure 3G on Cisco 800 routers as i didn't find any configuration guides for 800 series routers. I found for 1800 ..
Hi, I have 2 AP's that were once connected to the WCS server but have been sitting on the side for awhile. When I powered them up and tried to reset them to factory defaults via the Clear Cnfig option in WCS, i got the error "Command failed". I a...
Good day,I am looking for a wireless solution to be intergrated into an existing LAN. It is a 3 story building with many wall and segregations seperating rooms etc. I want to enable wireless capability throughout the building. I was looking at the...
Hi,I bought this AP (http://www.cisco.com/en/US/products/ps10052/index.html) to get acceptable speed when accessing my servers.I configured the device, installed an N standard wifi card in my PC.Signal strenght is excellent, it says 130Mbit/s.When I ...
Hi,I have a WLC 4402-40 with code 5.0.148.0 with 27 APs.Two APs are often disassociated from the WLC.Two APs are the same model of others and all APs are in local LAN.This is the Time Statistics:Time StatisticsUP TimeController Associated TimeControl...
Hi I use WCS v6.0.132.0 to manage my 4402 and 2106 controller both running version 6.0.182.0When I try to add another 2106 over DM-VPN it fails with the following errors:”No response from device, check SNMP communities, version or network for issues”...
Hello all,I have two WAP4410N's that are about 30 feet apart in seperate buildings. I'm trying to bridge them and their wired networks together with no luck.I would like each to also accept wireless connections.They are both configured on the same s...
