Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have an LWAP connected to WIsn on 6500. I want to clear the config and manually configure static IP to set it up on a network where I do not have any DHCP server.I read in the doc: http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tec...
I am planning on setting up a Hub and Spoke Wireless Bridging Scenario, with a 1242 Access Point as a Hub and 871W Routers (with PC's attached) at the Spokes.Cisco does mention that 870 Series Routers do not support repeater or bridging functionality...
Hi,I have configured radius setting on the wireless controller. After applying setting I lost the control. I want to break the password. Pl let me know how I cn be able to break pasword of 4400 wireless controller.Thanks in Antiscipation.
Hi,i have a problem wich my ap 1250. I did the basic config by CLI but when i plug it on the switch, the switch port change to up but 5 seconds after the port change to down. In the midle of the switch and the AP i use the AIR-PWRINJ4.I only config t...
Resolved! Root bridge and non-root-bridge issue?
hi all,for my network (look diagram)i want use in each AIR-AP1242AG-E-K9 twO antenna (AIR-ANT5195P-R=used for 802.11a and AIR-ANT24120=used for 802.11G)look in the diagram and tell me:-it is possible with my AP-1242?if yes,says me how to configure AP...
If I use the locally generated SSL cert on my WLC Internet Explorer always shows the "Untrusted cert warning" when users try to authenticate via the web interface. What can I do to resolve this do I need to buy a cert? If so where is the best and c...
Hi,Rolling out some LWAPs controlled by a 4402 WLC switch. The on-line help/docs say you can install a public SSL cert (for example from Verisign) for Web based user authentication but there is no Certificate Signing Request (CSR) capability that I c...
Hi!I have little problem. When i connect LAP to switch, use PowerInjector, i got message on WLC - *AP's interface:1(802.11b) Operation Status Down:Base Radio MAC:xxxxx Cause=Low in-line power*But if I use switch with PoE - all ok.Somebody know what t...
Can a 1300 wireless bridge/ap be set to associate to a non Cisco Access point as a client in AP mode? Is this possible or are the 1300's only capable of associating to Cisco Bridges in Bridge mode?
I have implemented a WISM on 6500, with WLAN defined for windows client using PEAP. Authenticaiton server is MS IAS server with SSL certificate installed.Now the users are connecting and authenticated fine. Problem;When the user disconnect and try to...
hi;Is that AIR-AP1242AG-E-K9 can work simultaneously in AP and Bridge modethank for your help
Ultimately the user needs to see a custom "splash page" without having to authenticate. I have successfully installed a custom web-auth bundle that appears when the WLAN Web Policy is enabled, but without any authentication, there is no access to the...
I have:12 - Cisco 7921 phones1 - (Offsite, within our WAN) 10 - 1242 APs connected to 3560sI need to connect the phones in a way that provides as much security as possible with minimal latency. What configuration and implementation do you recommend t...
adquirà un access point air-lap1131ag-a-k9 y no logro configurarlo ya que en el modo exec privilegiado no me aparece el comando configure
Hello,I am trying to configure a network layout like this:LAN0-871W-Dot11Radio ))) ((( Dot11Radio-SomeotherrouterI want to connect the routers through over the dot11Radio but am unsure as to how to configure the 871W to do this. Any suggestions or li...
