Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

I have a strange one. If I take a new access point to one of our remote and plug it in, it will not join the controllers at the home location (running latest 4.2) but it will eventually find one of our 2106 controllers running 5.1. If I take an acces...

Hello,Once or twice each week our organization's wireless stops working. When this occurs, individual do get an IP, but cannot ping the router. I can resolve the issue by doing a shut / no shut on dot11radio 0. Is this a configuration error (I don't ...

drewscarter by • Community Member
  • 509 Views
  • 0 replies
  • 0 Helpful votes

THe latest code has a new feature described below. Does that help with the issue of moving all APs off a controller prior to upgrading the controller. If so it would be very welcome. Also, the lastest MD code is 4.2.207.0. I have been running 5.2.178...

cef2lion2 by • Level 4
  • 828 Views
  • 1 replies
  • 0 Helpful votes

Hello.I have recently setup a WLC at a loctaion.Everything is fine excpet the guest access.I have selected Web-Auth for the guest wireless network.Users can connect to the guest network with no isses, but when they open IE the web login page doesn't ...

RVirdi by • Level 1
  • 1057 Views
  • 2 replies
  • 0 Helpful votes

Hi,Has anyone been able to configure restrictive access to the Management interface? I created an ACL that specifies our Management VLAN and set the action to "permit". I then added this ACL to the management interface, but I'm still able to login fr...

john.judge by • Community Member
  • 680 Views
  • 0 replies
  • 0 Helpful votes

Hi GuysI need someone can help me please, my problem is this:We have a wireless mesh network with 2 WLC and 24 LAP1510AG (4 RAPs), which are registered to the WLC 1 when tested HA, i turn off the WLC 1 to operate the WLC 2, there were only 12 of the ...

pgonzalez by • Frequent Visitor
  • 1390 Views
  • 4 replies
  • 0 Helpful votes

In order to replicate a bug, I'm looking to add a Cisco WAP to my lab which has an ssh banner of SSH-2.0-OpenSSH_4.0.Does anyone know of a hardware / software version which runs this version of SSH?I have a 350, 1100 and 1220B but they are all runnin...

jhansen by • Community Member
  • 892 Views
  • 0 replies
  • 0 Helpful votes

Hi there,I have a question with respect to DHCP Proxy to an external DHCP server. Is it possible to force the DHCP proxy to use the Management Interface as the source for all DHCP requests? My Wireless setup has all the dynamic wireless VLAN's going ...

Hi.I have a problem with unified solution.This is scenario:Client scanners mod. DENSO))((AP1230 automous))((telnet to AS400Mod. Denso BHT210BW, after 5 min of inactivity the client activates the standby mode, disable the radio.The warehouseman press ...

severi by • Level 3
  • 960 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Auto RF

We just setup auto RF on all of our 12 controllers. My question is, is the controller group leader the only controllerthat will display the "Last Group Updates" times? or should I see it on all the controllers?

HiI am new to the CISCO forums and could not find info where I searched, so of someone can point me in the right direction it will be much appreciated.We want to roll out Voice over Wireless LAN networks for a company, I need to investigate specific ...

admin_2 by • Level 7
  • 2904 Views
  • 5 replies
  • 0 Helpful votes

hi folks: Has anyone of you tried to convert autonomous to lwapp mode? I used upgrade tool v3.4 and it said 1140 is not supported. Or is there any other way to do the conversion? Thanks.regardsAlex

ita_hsieh by • Level 1
  • 3709 Views
  • 2 replies
  • 0 Helpful votes