I would to get clarification on the function of the different AP Modes in the WAP4410N Access Point. I would also like to look at some examples of how to use the various AP Modes to expand a wireless / wired infrastructure.
I would to get clarification on the function of the different AP Modes in the WAP4410N Access Point. I would also like to look at some examples of how to use the various AP Modes to expand a wireless / wired infrastructure.
Folks, I have seen strange problem in WiSM, while configuring as service vlan, I could see the status of one of the service vlan's as Oper-Up. Second one is mentioned as -- , whereas I could access both wism by means of html. Through CLI i could acce...
Hi AllI have been asked to configure MAC Address authentication on a WLC4402 without the use of a RADIUS Server or Cisco ACS. I remember that an autonomous AP has a limit of 20 MAC Addresses in the local list.Does anyone know if this limitation is st...
I have converted 2 standalone 1131AG to LWAPP. On the 4404 controller, both AP's says "Admin status=enabled" and "Oper status=down". How can that be ?
I have a customer that purchased 1141 LAP by mistake as he does not have a controller. What he wants is to use them Standalone. Is there an image that can be downloaded to convert these AP's to Standalone mode?Thanks,Ken
AP1231G-E-K9 was converted to a thin client AP to be managed on a controller.After a 'succesfull' conversion, the AP did registered with the controller, but since it's located at a remote site, it was be be coverted run HREAP. The AP is connected on ...
Could we use an 1140 or a 1230 to bridge or relay (no network drop) to an existing WLC system?
Hello,Is there a way to stop RIM (Blackberries) and iPhones, Nokia's and Sony from connecting to the guest network as they hog IP addresses? I would like to do some "range" mac filtering or sommat, but only for iphones, and rim, and mobile devices, b...
Hi all. I am hoping someone can assist me with this.I have 10 APs (all 1242s) and a WDS (also running on a 1240 Aironet). All of the APs authenticate to the WDS successfully. The WDS uses it's own local RADIUS server for authentication and there is a...
hi what is the steps to configure EAP FAST from ACS V5 and in DEL and HP wirless clientsin additional CAN ACSv5 support EAP TLS?Regards
I have a 871W I am going to use for a conferance in hotel. There will be 30-35 users. Not all will be wirelss but most of them will. How may clients can a 871W support? I also have a 1242 Aironet. Would I be better using that?
We use AP1230's as AP's and as workgroup bridges (WGB's) so we have Cisco on both ends of the RF link. We'd like to control the amount of upstream bandwidth from wireless clients while leaving the download side unrestricted.IOS on routers supports th...
HiI've just upgraded WCS from 4.2.128.0 to 6.0.132.0 But WCS won't start. The hm_launchout.txt file show:Starting Health Monitor as a primaryChecking for port 8082 availability⦠okStarting Health Monitor Web Serverâ¦Health Monitor Web Server Start...
"1252 both radios installed w/one radio enabled @ full N speed on 802.2af power"Are there any special instructions to make this work as described in the documentation for the latest SW Version 12.4(21a)JA1?"Support for 802.11n Performance on 1250 Ser...
I installed a Cisco Aironet 1200 access point for use with a few Macs, some old Dell D600 and iPhones. I have enabled both G and A netorks (tried various channels as well) and cannot get the old Dell D600 and/or iPhones (3G and 3GS) to see the networ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-17-2026 11:43 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |