Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Insider User Research program

Labels

Forum Posts

We have 1131 LWAP's and WCS v.5.0.56.2On the controller you have a checkbox when configuring AP's that enables the AP's to override the POE capabilities of the switch. I've been searching in the WCS for the same checkbox, but cant find it. Has Cisco ...

s.hellman by Level 1
  • 1216 Views
  • 1 replies
  • 0 Helpful votes

I have a WISM running code 4.0.179.11.~250 APs connected (1131) all switchports configured on 100/full.Around 30% of the Aps are having duplex/speed mismatches. If i change the connected switchports to AUTO the APs nicely return on 100/Full.Anyone ha...

I met some problem with associate Nokia's dual mode mobile phone E61i with Cisco WLC 4402, hope someone can help me on it:I setup a VOICE WLAN in 4402(v5.0.148), Layer2 security is WPA1+WPA2, Key management using 802.1x, WPA1 policy enable both TKIP ...

bbxie by Level 3
  • 1378 Views
  • 8 replies
  • 0 Helpful votes

Guys Im trying to setup Guest access for our visitors. I have 4 internal controllers up and running with v4.1.185 and no issues. We have just purchased an additional WLC that we want to setup on our DMZ for guest access. We have done all required Anc...

I have 20+ Cisco Aironet 1100's. What I would like to do is create 2 SSID's 1 to be broadcasted and the other not. The one that is not broadcasted is going to be in use for 802.1x with a RADIUS server. The SSID that is broadcasted would like the be u...

one3cap12 by Level 1
  • 594 Views
  • 2 replies
  • 0 Helpful votes

I bought an Aironet 1220A series AP. I can't get to priviledge mode and I have tried to reset the AP to no avail. Does any know the trick to reset the AP?Here is some info about the AP:From bootup sequence - cisco AIR-AP1220-IOS-UPGRD (PowerPC405GP)...

jeffleung by Level 1
  • 1014 Views
  • 1 replies
  • 0 Helpful votes

Hi all,I get a lot of the following syslog error messages from 3 of my 4 WLCs (two WiSMs).Error message:ethoip.c:342 ETHOIP-3-PKT_RECV_ERRORI searched at cisco.com and I found the information to use the bug toolkit or open a tac case, but I didn't fi...

weymannpe by Level 1
  • 740 Views
  • 2 replies
  • 0 Helpful votes

The information is not clear to me. We have a couple of Cisco Wireless access point that we just bought. After running an EoS/EoL report using CiscoWorks, they show up on the list like "Cisco Aironet 1210 Access Point" as a device that has announce E...

lm20ele by Level 1
  • 2210 Views
  • 2 replies
  • 0 Helpful votes

Weirdest thing:We are trying to register one 1522 Mesh AP (the one with a Cable Modem inside) to a controller using the lastest mesh image. Here is the thing:For some reasong, the AP was previously associated to a different Controller, (lwapp command...

My company is looking at delpoying wireless in some small remote offices, we are looking at using the NM-AIR-WLC6 module in our current 2821 routers running 12.4.7d. Unfortunately our standard version of IOS doesn't support the NM. So I am looking ...

cwhayes by Level 1
  • 392 Views
  • 2 replies
  • 0 Helpful votes

hallo,I have 2 Air-AP1242-AG-E-K9 access point.Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(8)JA2, RELEASE SOFTWARE (fc1.I'm configuring one of them to be an HOT STANDBY of the other.The HOTSTANDBY ap associates to the MAIN ap but ...

fsoffia by Level 1
  • 433 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card