Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

  Hi team, In my environment, I've noticed an anomaly with our 500 APs. Around 450 of them are establishing CAPWAP tunnels with 1485 MTU, while the remaining 50 are using   1005 MTU.  AP Model: 9166 {All APs are in local mode}  WLC: 9800 is it any bu...

Sanju_13 by Frequent Visitor
  • 4385 Views
  • 7 replies
  • 0 Helpful votes

Hello guys,i am going here for advice.I have a project where is planning MX75, 3Meraki switches and 19APs(MR28)....but this will be done in summer.Now i am trying to configure IPSK without radius and there is still some problems.My lab is(MR67 + MS12...

VanDerTuch by Community Member
  • 3331 Views
  • 5 replies
  • 0 Helpful votes

I am having an issue with getting some new 3702i APs to join a new 5520 WLC.  I am trying to add about 180 Aps to this controller and none of them join.  I see them trying to join in the AP Join section, but all are unsuccessful.  I have another new ...

jvasilko by Level 3
  • 6760 Views
  • 12 replies
  • 0 Helpful votes

We configured our C9800 with a Dot1x SSID. when clients enter access to connect, we have the following message Mar 7 14:11:37.180: %DOT1X-5-FAIL: Chassis 1 R0/0: wncd: Authentication failed for client (f446.3742.4aa0) with reason (Cred Fail) on Inter...

Hashen by Level 1
  • 3192 Views
  • 9 replies
  • 0 Helpful votes

Hi All, In one of our SSID we made some changes to the duration of splash page and added AD login for users. Before we made these changes SSID was open for all users. After making the changes I can still see there are clients connected from the previ...

BeepBop by Community Member
  • 2907 Views
  • 1 replies
  • 0 Helpful votes

Hello Cisco WLAN Community,we are struggling here using a new 9800-L-C HA-Anchor WLC running 17.3.4 for guests in our hospital.The Foreign WLCs are 2 5520-WLcs and 1 9800-80.During peek-times we see around 3000+ users on this box. But suddenly, the w...

Gehrig_W by Level 6
  • 6236 Views
  • 11 replies
  • 0 Helpful votes

Hi everyone, I have C9800 17.09.04a and C9120AXI-E with 802.11r enabled but in some case the clinet doesn't work correctly,instead to use the FT works with normal roaming (eap and 4WH). Devices Dell and HP. someone can help me?

cla7109 by Community Member
  • 1137 Views
  • 2 replies
  • 0 Helpful votes

Hi All,We have a dedicated SSID for Voice Picking Devices (VPD) with 802.11r enabled, totalling approximately 53 devices.I've noticed that 2 devices are not 802.11r-compatible, as indicated by the Meraki dashboard under Capable Wi-Fi standards.My que...

SuperM by Community Member
  • 2405 Views
  • 3 replies
  • 0 Helpful votes

Hi,we are running 9800 CL for some time now and have issues with PSK SSIDs. We have couple of them and the same issue appears on all of them despite slighly different configuration. The issue I see on DNAC for those clients is always like this:Detail...

sroic by Level 3
  • 2201 Views
  • 1 replies
  • 0 Helpful votes

Resolved! 1300 Bridge ??

I have got a question about the Cisco Aironet 1300 Series Outdoor Access Point/Bridge with Integrated Antenna. Can I use this model to be used outside. In other words mounted on the roof top where it is exposed to rain, sun, lightning etc. We have to...

Review Cisco Networking for a $25 gift card