Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi All,Have just put the QoS configurations on the WLC for a Voice WLAN and Can see that the Phone is setting the QoS Marking on frames from the 7921G to the WLC with the following : QoS Control Priority: 6 (Voice) (Voice) Ack Policy: Normal Ack (0x0...

I have one WCS running 3.0.101.0. Currently there are few WLC's(inturn supporting Cisco 1010 AP's) associated with it which are running 3.2.150.6 and 3.2.195.10. I have one more WLC which is running 4.2.61.0 which is not getting added in WCS. I came ...

syed_masir by • Community Member
  • 1203 Views
  • 4 replies
  • 0 Helpful votes

I have a demo kit that includes a 2106 WLC and 2 1252 WAP. I have configured the WLC correctly (I think) and the 2 WAP can contact the WLC when they are plugged directly into the WLC and I can connect my laptop wirelessly. I want to move the WAP's fr...

ryanrock by • Community Member
  • 2401 Views
  • 4 replies
  • 0 Helpful votes

Hi,I'm currently running both a WCS appliance and a windows server WCS on version 4.2.62.11They are managing around 1000 AP's that are in a Hospital environment. They are using Vocera badges.The controllers are all running v4.2.61.0What are my best u...

pic_whizz by • Level 2
  • 2388 Views
  • 12 replies
  • 0 Helpful votes

Hi, I will make an abbreviation report about my case. My WLC 4402 was running 4.0.217.0 version. There are 18 access point work with local. It's work fine.To a new project, we will add a access point 1522 and others 1242 to extend the range to a smal...

rezende.c by • Level 2
  • 951 Views
  • 1 replies
  • 0 Helpful votes

Hello All, I need some inputs so as to is this can be done, I have a Lynksys wireless setup in my Office,1. I want to know which user is connected to the wireless2.What is the signal strength that he is getting, or how far is he from the Ap.3.A detai...

Amitdivekar by • Community Member
  • 1356 Views
  • 1 replies
  • 0 Helpful votes

I have two Cisoc AP 1131's. One is upstairs and the other is downstairs. I am getting complaints from users that they are getting dropped from the wireless network and sometimes a user upstairs may connect to the WAP downstairs. Is there a way to con...

gbarden by • Level 1
  • 1758 Views
  • 3 replies
  • 0 Helpful votes

After upgrading the controllers from 4.2.61 to 5.2.157 (with intermediate 4.2.176 upgrade) I was not able to change the name, or any other parameters of a newly joined 1242 LWAPP. There were no error messages, it just didn't work. I finally fixed it ...

crcooley by • Community Member
  • 400 Views
  • 0 replies
  • 0 Helpful votes

I have 3 APS (two 1242s and one 1142) and am trying to get them to connect to a WLC4402 running 5.2.157.0The 1142 is registered ok but both 1242s are failing with the same error.Both 1242s acquire an ip address via DHCP and both are pingable from the...

s-moynihan by • Community Member
  • 1568 Views
  • 6 replies
  • 0 Helpful votes

My customer has a 526 WLC installed in a guest Pavilion. It is supporting 5 521 Access Points. Yesterday the customer wanted to know if there was a way that they could from the WLC shut down access to the Wireless Network. They have a group in and DO...

Review Cisco Networking for a $25 gift card