Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi,Couple of days ago I wrote about not being able to configure my ap's 1602i to work as root and repeater. Today I have different problem. When I tried to connect my pc to repeater device using ethernet cable I didn't get access to network. I tried ...
Hi all,I have WLC 5508 and I faced a problem joining all ap (not join). After I search, the problem is th MIC.So I do the following:1- Set date of WLC to date before AP MIC Expired.2- I upgraded the WLC from 8-2-170-0 to 8-5-151-0 (I did not restart ...
Hi, I am trying to configure three C9136I-ROW access points. I could give the primary and secondary controller details, but I cannot get them on the controller.Below is the error that keeps on popping up in my putty session,*01/31/2024 12:16:31.0404]...
I'm enabling export anchor on a 9800 for a coproprate network. The policy currently is applied to a number of SSID, so I've cloned the policy and enabled the 'Export Anchor' config.The Foriegn anchor is an AireOS 5520, I've created an idently named S...
Resolved! Picture of the MR46E antenna ports ?
Do anyone have a picture of the MR46E antenna ports / layout ?On the datasheet and installation guide, there is no "map" of what port it for scanning, IoT and the normal 2,4/5 WiFi.ThanksThomas
Resolved! Restrict Access
Do you guys know if it is possible to restrict access to an SSID only by workstations and not mobiles?
Hello, I hope you are well, I would like to add access points on my 5500 series controller, but the equipment is end of life. is it possible to get a new license for my new access points or do i have to buy a new controller. Current equipment (5500 S...
HI Team, i have Cisco 9800 model wlc and ap model 9120axi running version 17.9.3 issue :Max retransmissions to AP ap automatic dis join to wlc and automatic join agin so can we enable in link latency ? ( if yes what is impact ) can we Adjust MSS s...
Resolved! ap 9115 log
hello I have a question about the ap log. I'm trying to complete the ap set and connect, but this log has occurred and I can't connect. log "wncd:Authentication failed for client (f0f5.6444.93d8) with reason (AAA Server Down) on Interface capwap_9...
hello Connecting 9115 ap. The ping goes to the radius server and the ssid is also seen on the phone. The problem is, I can't connect even if I press ssid. ID/PW is correct. ID/PW is successful even with the test aaa group command. I think there is ...
Hello everyone, i have installed Cisco 9800-CL virtual WLC on vmWare ESXi. current setup lools like : WLC has dedicated MGMT interface(GIG1) and trunk port (GIG2). Cisco VPC is configured with ESXi standard switch, with active passive uplink ports...
Resolved! AP 185X and 9115 Firmware update
Hi My Wi-Fi Network setup is mixed APs model. when we are trying to update the Firmware through EWC - HTTP method is not possible because the non homogenous model. Suppose i try to update the firmware via TFTP. the updated image is running in the ba...
Hello everybody,Recently, I bought a Cisco (AIR-LAP1142N-A-K9) device and reset it to the factory default via the terminal port(COM3).Now, I have access to its Web interface through its LAN perfect.How can I connect it to my home WiFi? I can not figu...
I am currently staying at a hotel that utilizes Cisco Meraki. Current ping/latency is 77ms. However, when I play a game (Rainbow 6) my ping/latency jumps to 250+. Anyway to fix this? IPv6 is not enabled through the hotel. Or is there a way I can prio...
Resolved! Cisco 9136 Lag/lacp on switches
Hi All, Trying to make full use of the 9136 dual port. Enable LAG on WLC 9800-L-C for AP Profile.However, the ports configured with LACP won't work on the switch side.when I switch to the Normal Trunk port it works.Does the AP not need LACP on switch...
